Yamaha 2010 WaveRunner VX Cruisel Скачать руководство пользователя | Manualshive

Страница: 42 / 106

background image

Watercraft operation

37

EJU40000

Watercraft operation modes

EJU31417

Low RPM Mode (VX Deluxe /
VX Cruiser)

The Low RPM Mode is a function that limits
the maximum engine speed to approximately
90% of the maximum engine speed in the nor-
mal mode.
The Low RPM Mode can only be activated
and deactivated by operating the remote con-
trol transmitter that is included with this water-
craft. (See page 30 for information on the
remote control transmitter.)

TIP:

The Low RPM Mode can only be activated
when the engine is stopped in the unlock
mode of the Yamaha Security System.

Activating and deactivating the Low RPM
Mode

Activation of the Low RPM Mode will be con-
firmed by the number of beeps when the re-
mote control transmitter is operated, and by
the “L-MODE” indicator light of the multifunc-
tion information center. (See page 39 for infor-
mation on the multifunction information
center.)

TIP:

If the remote control transmitter is operated
while the multifunction information center is in
the standby state, the center performs the ini-
tial operation, and then the setting is selected.
To activate the Low RPM Mode:
Push the “L-Mode” (unlock) button on the re-
mote control transmitter for more than 4 sec-
onds. Once the beeper sounds three times
and the “SECURITY” indicator light blinks
three times, then comes on, the “L-MODE” in-
dicator light comes on and the Low RPM
Mode is activated.

TIP:

If the Low RPM Mode is activated immediate-
ly after the information display turns off, the
“L-MODE” indicator light will not come on. The

1

Remote control transmitter

Number of

beeps

Low RPM Mode

operation

“L-

MODE”

indicator

light

Activated

Comes

on

Deactivated

Goes off

UF2N10E0.book Page 37 Tuesday, October 6, 2009 5:02 PM

«
...
40
41
42
43
44
...
»

Содержание 2010 WaveRunner VX Cruisel











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 WaveRunner VX Cruisel

Бренд: Boston Whaler Страницы: 82

SEASCOOTER AQUA RANGER SD95001

Бренд: Sea-doo Страницы: 16

Бренд: SEVEN BASS DESIGN Страницы: 4

Бренд: S/C Yachts Страницы: 10

Бренд: Pelican Страницы: 2

Бренд: World Cat Страницы: 74

Бренд: World Cat Страницы: 91

Бренд: World Cat Страницы: 98

Бренд: Zodiac Страницы: 63

WaveRunner FX SVHO

Бренд: Yamaha Страницы: 174

Бренд: Yamaha Страницы: 116

Бренд: Yamaha Страницы: 144

40 Trawler Single

Бренд: Mainship Страницы: 170

Бренд: Four winns Страницы: 185

Бренд: Rave Sports Страницы: 13

GLACEIR BAY EDITION 2770

Бренд: WORLDCAT Страницы: 100

Бренд: RYDS Страницы: 56

Бренд: Key West Boats Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды