Yamaha 2009 XV250Y Скачать руководство пользователя | Manualshive

Страница: 50 / 84

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-15

7

TIP

The tire tread depth limits may differ
from country to country. Always comply
with the local regulations.

WARNING

EWA10560

●

It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

●

The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

●

It is not recommended to patch
a punctured tube. If unavoid-
able, however, patch the tube
very carefully and replace it as
soon as possible with a high-
quality product.

Tire information

This motorcycle is equipped with spoke
wheels and tube tires.

WARNING

EWA10461

The front and rear tires should be of
the same make and design, other-
wise the handling characteristics of
the vehicle may be different, which
could lead to an accident.

After extensive tests, only the tires list-
ed below have been approved for this
model by Yamaha Motor Co., Ltd.

EAU21940

Spoke wheels

To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage, and
the spokes for looseness or dam-
age before each ride. If any dam-
age is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

Front tire:

Size:

3.00-18 47P

Manufacturer/model:

CHENG SHIN/C-916

Rear tire:

Size:

130/90-15M/C 66P

Manufacturer/model:

CHENG SHIN/C-915

U2UJ26E0.book Page 15 Thursday, May 22, 2008 10:21 AM

«
...
48
49
50
51
52
...
»

Содержание 2009 XV250Y





















































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 XV250Y

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: Yamaha Страницы: 92

Бренд: hepco & becker Страницы: 6

Бренд: Braaap Страницы: 40

DaVinci RSV4-APRC

Бренд: STARLANE Страницы: 2

690 Enduro R 2019

Бренд: KTM Страницы: 274

Бренд: Zontes Страницы: 119

Firstgear 512817

Бренд: Dennis Kirk Страницы: 2

Бренд: DYNATEK Страницы: 4

Бренд: DYNATEK Страницы: 5

Бренд: DYNATEK Страницы: 4

Evoline 3 Series

Бренд: Shark Страницы: 31

Бренд: Shark Страницы: 36

X-FORCE PRO 50 2017

Бренд: Kuberg Страницы: 28

Бренд: PORTMAN Страницы: 13

Бренд: KTM Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды