Yamaha 2009 XV250Y Скачать руководство пользователя | Manualshive

Страница: 17 / 84

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-1

4

EAU10450

Main switch

The main switch controls the ignition
and lighting systems. The various main
switch positions are described below.

EAU10480

ON

All electrical systems are supplied with
power, and the headlight, meter lighting
and taillight come on, and the engine
can be started. The key cannot be re-
moved.

EAU45751

OFF

All electrical systems are off. The key
can be removed.

WARNING

EWA10072

Never turn the key to “OFF” while
the vehicle is moving, otherwise the
electrical systems will be switched
off, which may result in loss of con-
trol or an accident.

EAU10980

Indicator lights

EAU11040

Turn signal indicator light “TURN”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11070

Neutral indicator light “NEUTRAL”

This indicator light comes on when the
transmission is in the neutral position.

1. High beam indicator light “HIGH BEAM”

2. Neutral indicator light “NEUTRAL”

3. Turn signal indicator light “TURN”

U2UJ26E0.book Page 1 Thursday, May 22, 2008 10:21 AM

«
...
15
16
17
18
19
...
»

Содержание 2009 XV250Y





















































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 XV250Y

Бренд: Racelogic Страницы: 2

Бренд: Yamaha Страницы: 102

Бренд: klicbag Страницы: 2

Minirack 6602533 01 01

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 6

Бренд: Two Brothers Racing Страницы: 2

Бренд: Sinnis motorcycles Страницы: 68

Бренд: Shark Страницы: 80

Бренд: CRATONI Страницы: 44

Бренд: Sealey Страницы: 2

Бренд: SHARKS Страницы: 25

Бренд: hepco & becker Страницы: 3

Бренд: KTM Страницы: 53

Бренд: Gazzini Страницы: 60

Бренд: Laverda Страницы: 151

Бренд: Uclear Страницы: 18

Бренд: Ice Bear Страницы: 39

Бренд: Fantic Motor Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды