Yamaha 2008 YZF-R1X Скачать руководство пользователя | Manualshive

Страница: 76 / 108

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-27

6

EAU23022

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

CAUTION:

ECA10581

The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.

1. Clean the drive chain with kero-

sene and a small soft brush.

CAUTION:

ECA11120

To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

CAUTION:

ECA11110

Do not use engine oil or any other lu-
bricants for the drive chain, as they
may contain substances that could
damage the O-rings.

EAU23100

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING

EWA10720

Damage to the outer sheath may in-
terfere with proper cable operation
and will cause the inner cable to
rust. Replace a damaged cable as
soon as possible to prevent unsafe
conditions.

Recommended lubricant:

Engine oil

U4C821E0.book Page 27 Tuesday, July 17, 2007 11:37 AM

«
...
74
75
76
77
78
...
»

Содержание 2008 YZF-R1X













































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 YZF-R1X

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: Racelogic Страницы: 2

Бренд: DMC Страницы: 2

Бренд: SSR Motorsports Страницы: 39

Бренд: Suzuki Страницы: 440

Бренд: Nolan Страницы: 80

Бренд: Wolfman Страницы: 3

6513515 00 22-00-40

Бренд: hepco & becker Страницы: 7

Бренд: LSL Страницы: 12

80 MasterGuard (L+K)

Бренд: SCHUBERTH Страницы: 44

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 114

YZF-R1P 2001-2003

Бренд: Yamaha Страницы: 439

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 124

ROAD STAR XV16A

Бренд: Yamaha Страницы: 117

X MAX CZD300P 2022

Бренд: Yamaha Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды