Yamaha 2008 YZF-R1X Скачать руководство пользователя

Страница: 34 / 108

INSTRUMENT AND CONTROL FUNCTIONS

3-18

curs, use a gasoline of a different
brand. Use of unleaded fuel will extend
spark plug life and reduce maintenance
costs.

EAU13442

Catalytic converters

This vehicle is equipped with catalytic
converters in the exhaust system.

WARNING

EWA10860

The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work.

CAUTION:

ECA10700

The following precautions must be
observed to prevent a fire hazard or
other damages.

●

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.

●

Never park the vehicle near pos-
sible fire hazards such as grass
or other materials that easily
burn.

●

Do not allow the engine to idle
too long.

EAU33861

Seats

Rider seat

To remove the rider seat
Pull back the rear of the rider seat as
shown, remove the bolts, and then pull
the seat off.

To install the rider seat
Insert the projection on the front of the
rider seat into the seat holder as
shown, place the seat in the original po-
sition, and then install the bolts.

1. Bolt

U4C821E0.book Page 18 Tuesday, July 17, 2007 11:37 AM

Содержание 2008 YZF-R1X













































































































Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды

Yamaha 2008 YZF-R1X, Руководство пользователя

Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды