Yamaha 2008 XVS11AWX Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-20

6

system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-
trol and an accident.

EAU22270

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

EAU22321

Checking the front and rear
brake pads

Front brake

Rear brake

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

1. Brake pad wear indicator groove

U3B822E0.book Page 20 Tuesday, May 15, 2007 10:37 AM

«
...
66
67
68
69
70
...
»

Содержание 2008 XVS11AWX

































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 XVS11AWX

Бренд: Honda Страницы: 186

Бренд: SUR-RON Страницы: 50

Бренд: SUOMY Страницы: 84

SPORTCITY CUBE 125

Бренд: APRILIA Страницы: 157

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 2

Scorpion 608-30-10086

Бренд: Barnett Страницы: 2

Бренд: Xenith Страницы: 7

Бренд: Leatt Страницы: 26

Бренд: Leatt Страницы: 26

Бренд: Chicago Electric Страницы: 7

Бренд: Chicago Electric Страницы: 10

gtrack 7855 MyBASIC

Бренд: Gemini Страницы: 20

VarioProtect XXL-W TC AIR TH3

Бренд: schweisskraft Страницы: 28

Бренд: JohnnyPag Страницы: 27

350 EXC-F AUS 2012

Бренд: KTM Страницы: 292

Бренд: Rivco Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды