Yamaha 2006 V Star XVS650AV Скачать руководство пользователя страница 60

Страница: 60 / 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

5. To increase the clutch lever free

play, turn the adjusting nut in direc-
tion (a). To decrease the clutch le-
ver free play, turn the adjusting nut
in direction (b).

6. Tighten the locknut at the clutch le-

ver and the crankcase.

EAU22092

Adjusting the brake lever free
play

The brake lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the brake le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the brake le-

ver.

2. To increase the brake lever free

play, turn the adjusting screw in di-
rection (a). To decrease the brake
lever free play, turn the adjusting
screw in direction (b).

3. Tighten the locknut.

WARNING

EWA10630

●

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.

●

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic

1. Brake lever free play

1. Locknut
2. Brake lever free play adjusting screw

U3B720E0.book Page 18 Friday, April 15, 2005 1:34 PM

Содержание 2006 V Star XVS650AV





























































































Результаты поиска

Содержание 2006 V Star XVS650AV

Отзывы:

Похожие инструкции для 2006 V Star XVS650AV

Бренды по названию

Популярные бренды

Yamaha 2006 V Star XVS650AV, Руководство пользователя

Результаты поиска

Содержание 2006 V Star XVS650AV

Отзывы:

Похожие инструкции для 2006 V Star XVS650AV

Бренды по названию

Популярные бренды