Yamaha 2006 FZ6-S Скачать руководство пользователя

Страница: 75 / 94

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

EAU24360

Front wheel

EAU34390

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Lift the front wheel off the ground

according to the procedure on
page 6-34.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

3. Remove the brake hose holder on

each side by removing the bolts.

4. Remove the brake caliper on each

side by removing the bolts.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

5. Pull the wheel axle out, and then

remove the wheel.

EAU24860

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolts.

6. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

1. Wheel axle

2. Front wheel axle pinch bolt

1. Brake hose holder
2. Brake caliper

3. Brake caliper bolt

4. Bolt

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 13 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

U1B3E3E0.book Page 35 Friday, July 14, 2006 11:34 AM

Содержание 2006 FZ6-S































































































Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды

Yamaha 2006 FZ6-S, Руководство пользователя

Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды