Yamaha 2006 FZ6-S Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 94

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

6

EAU34380

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the bolts on each side.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10660

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al-
cohol or thinner.

1. Bolt

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder
2. Headlight bulb

U1B3E3E0.book Page 31 Friday, July 14, 2006 11:34 AM

«
...
69
70
71
72
73
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: Kask Страницы: 68

Бренд: R&G Страницы: 4

Бренд: MadStad Engineering Страницы: 8

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

Бренд: Miller Страницы: 12

Бренд: Nuviz Страницы: 46

Splendor Pro CLASSIC

Бренд: HERO Страницы: 56

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды