Yamaha 2006 FZ6-S Скачать руководство пользователя

Страница: 66 / 94

PERIODIC MAINTENANCE AND MINOR REPAIR

6-26

EAU23200

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10730

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

EAUM1650

Lubricating the swingarm piv-
ots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease

U1B3E3E0.book Page 26 Friday, July 14, 2006 11:34 AM

Содержание 2006 FZ6-S































































































Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды

Yamaha 2006 FZ6-S, Руководство пользователя

Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды