Yamaha 2006 FZ6-S Скачать руководство пользователя | Manualshive

Страница: 53 / 94

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-13

6

the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.

12. Install the coolant reservoir cap.
13. Install the radiator cap, radiator

cap retainer and radiator cap re-
taining bolt.

14. Start the engine, let it idle for sev-

eral minutes, and then turn it off.

15. Remove the radiator cap to check

the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radia-
tor, and then install the radiator
cap, radiator cap retainer and radi-
ator cap retaining bolt.

16. Check the coolant level in the res-

ervoir. If necessary, remove the
coolant reservoir cap, add coolant
to the maximum level mark, and
then install the cap.

17. Start the engine, and then check

the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.

EAU34423

Replacing the air filter element

The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.

1. Remove the seat. (See page

2. Remove the fuel tank bolts, and

then lift the fuel tank away from the
air filter case.

3. Remove the air filter case cover by

removing the screws.

1. Radiator cap retaining bolt

2. Radiator cap

3. Radiator cap retainer

1. Bolt

U1B3E3E0.book Page 13 Friday, July 14, 2006 11:34 AM

«
...
51
52
53
54
55
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 44

Бренд: KTM Страницы: 29

Бренд: CF MOTO Страницы: 443

Бренд: Miller Страницы: 12

Бренд: Denali Страницы: 2

Бренд: X-lite Страницы: 38

RACE 11621C0520

Бренд: Yoshimura Страницы: 7

Бренд: Aim Страницы: 47

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 34

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 92

WARRIOR XV17PCT

Бренд: Yamaha Страницы: 97

WARRIOR XV17PCC

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды