Yamaha 2006 FZ6-S Скачать руководство пользователя страница 28

Страница: 28 / 94

INSTRUMENT AND CONTROL FUNCTIONS

3-14

or premium unleaded fuel. Use of un-
leaded fuel will extend spark plug life
and reduce maintenance costs.

EAU13411

Fuel tank breather hose

Before operating the motorcycle:

●

Check the fuel tank breather hose
connection.

●

Check the fuel tank breather hose
for cracks or damage, and replace
it if damaged.

●

Make sure that the end of the fuel
tank breather hose is not blocked,
and clean it if necessary.

EAU13441

Catalytic converter

This vehicle is equipped with catalytic
converters in the exhaust system.

WARNING

EWA10860

The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work.

CAUTION:

ECA10700

The following precautions must be
observed to prevent a fire hazard or
other damages.

●

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.

●

Never park the vehicle near pos-
sible fire hazards such as grass
or other materials that easily
burn.

●

Do not allow the engine to idle
too long.

1. Fuel tank breather hose

2. Original position (paint mark)

U1B3E3E0.book Page 14 Friday, July 14, 2006 11:34 AM

Содержание 2006 FZ6-S































































































Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды

Yamaha 2006 FZ6-S, Руководство пользователя

Результаты поиска

Содержание 2006 FZ6-S

Отзывы:

Похожие инструкции для 2006 FZ6-S

Бренды по названию

Популярные бренды