Yamaha 2006 FZ6-S Скачать руководство пользователя | Manualshive

Страница: 25 / 94

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-11

3

EAU12733

Hazard switch “

”

With the key in the “ON” or “

” posi-

tion, use this switch to turn on the haz-
ard lights (simultaneous flashing of all
turn signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.

CAUTION:

ECA10061

Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-
tery may discharge.

EAU12820

Clutch lever

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-18.)

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

1. Clutch lever

1. Shift pedal

U1B3E3E0.book Page 11 Friday, July 14, 2006 11:34 AM

«
...
23
24
25
26
27
...
»

Содержание 2006 FZ6-S































































































Отзывы:

Нет отзывов

Похожие инструкции для 2006 FZ6-S

Бренд: APRILIA Страницы: 163

Бренд: N-Com Страницы: 6

Бренд: LAZER Страницы: 2

Бренд: R&G Страницы: 3

Бренд: GAS GAS Страницы: 150

Бренд: AGV Страницы: 64

Бренд: Crivit Страницы: 30

Бренд: A.J.S. Страницы: 94

DRAG STAR XVS125

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 82

CRUX REV YD110-1 2016

Бренд: Yamaha Страницы: 82

Diversion XJ600N

Бренд: Yamaha Страницы: 101

Drag Star XVS1100

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды