Yamaha 2006 FJR1300AS Скачать руководство пользователя страница 42

Страница: 42 / 150

ENGINE

– 33 –

d. Install a suitable bracket “4”, the magnet base

B “5”, and the dial gauge & stand set “6”.

e. Disengage the clutch by turning the manual

clutch operation bolt.

f. Measure the clutch pressure plate stroke.

g. If the pressure plate stroke is out of specifica-

tion, repeat steps (j) to (l) in the procedure for
step “2. Bleed” until clutch pressure plate
stroke is within specification.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

4. Install:

• Swingarm

Refer to “SWINGARM” in chapter 4. (Manual
No.: 3P6-28197-E0)

• Rear wheel

Refer to “REAR WHEEL” in chapter 4. (Man-
ual No.: 3P6-28197-E0)

• Air filter case

Refer to “GENERAL CHASSIS” on page 37.

ET2D21036

CHECKING THE VEHICLE AFTER
BLEEDING THE HYDRAULIC CLUTCH
SYSTEM

1. Check:

• Rear wheel drag torque

Rear wheel does not rotate/drag torque does
not progressively increase in the following or-
der: neutral, 1st gear, and when rear wheel
starts to rotate in 1st gear

→

Check the pres-

sure plate stroke.
Refer to “BLEEDING THE HYDRAULIC
CLUTCH SYSTEM” on page 31.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Place the vehicle on the centerstand.
b. Turn the main switch to “ON”.
c. Shift the transmission into neutral, and then

rotate the rear wheel by hand.

d. Shift the transmission into 1st gear, and then

rotate the rear wheel by hand.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

2. Check:

• Shift operation

Engine stalls

→

Check the pressure plate

stroke.
Refer to “BLEEDING THE HYDRAULIC
CLUTCH SYSTEM” on page 31.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Place the vehicle on the centerstand.

Magnet base B

90890-06844

Magnetic base stand

YU-A8438

Dial gauge & stand set

90890-01252

a. 100 mm (3.94 in)
b. 20 mm (0.79 in)
c. 1.5 mm (0.06 in)
d. 64 mm (2.52 in)
e. M6

40 mm bolt

5 mm (0.20 in)

g. 60 mm (2.36 in)

Clutch pressure plate stroke

2.8 mm (0.11 in) or more

Содержание 2006 FJR1300AS























































































































































Результаты поиска

Содержание 2006 FJR1300AS

Отзывы:

Бренды по названию

Популярные бренды

Yamaha 2006 FJR1300AS, Руководство по обслуживанию

Результаты поиска

Содержание 2006 FJR1300AS

Отзывы:

Бренды по названию

Популярные бренды