background image

GT-222ES, SRM-222ES, F226S, T226S, C226S

10-21U-00

1

INTRODUCTION

W

e are constantly working on technical im-

provement of our products. For this reason, 
technical data, equipment and design are 
subject to change without notice. All speci-
fications and directions in this SERVICE 
DATA are based on the latest product infor-
mation available at the time of publication.

1

SERVICE DATA

TRIMMER/BRUSHCUTTER

ECHO: 

GT-222ES/SRM-222ES

shindaiwa:

 

F226S/T226S/C226S

STAGE    MODEL

(Serial number : 37000001 and after)

CONTENTS

 

page

1 SERVICE INFORMATION

 .............................. 2

1-1 Speci

fi

 cation ............................................... 2 

1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4  Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6

2 CARBURETOR ADJUSTMENT PROCEDURE

 ...7

2-1  General adjusting rules ............................... 7
2-2  Presetting Idle adjust screw, Idle mixture 
needle and Hi speed mixture needle ................. 7
2-3 Adjusting carburetor.................................... 8

Reference No.

 

10-21U-00

I S S U E D :     2 0 1 2 0 6

Содержание Echo SRM-222ES









Отзывы: