manualshive.com logo in svg

Yale 4H42, Руководство пользователя, Страница: 10 / 36

Поделиться
Скачать
Yale 4H42 Скачать руководство пользователя страница 10

2  Safety-related information 

 

 LS Open Loop Vector Motor 4H42, 4H71, 4H72 Manual Supplement 

 

za-o.2.8.41-us-1.1 

August 2022 

 

Page 10 

za

-o.

2.

8.

41

-us

-1

.1 

2.3.4

 

Personal protective equipment 

Personal protective equipment must be worn at all times during activities that can cause 

injuries or endanger health. 

 

To be worn at all times 

 

Work protective clothing 

Work clothes with low tear resistance, with narrow sleeves and no  

protruding parts, to protect against being caught by moving machine 

parts. Do not wear rings, chains or other jewellery. 

 

Safety shoes 

For protection against heavy falling parts and slipping on slippery  

surfaces. 

Wear in unusual environmental conditions 

 

Safety eyewear 

To protect the eyes from any stray flying parts and splashes of liquid. 

 

Hearing protection 

To protect against hearing damage. 

 

Safety helmet 

For protection from falling parts. 

 

Safety gloves (only if there is no entanglement hazard) 

To protect hands from friction, abrasions, punctures or deep injuries as 

well as from contact with hot surfaces. 

 

Safety harness 

It is necessary to provide work rigs or lifting platforms for any  

maintenance and repair work that cannot be carried out from floor level. 

Service technicians who work outside lifting platforms must be safe-

guarded with a safety harness. 

 

 

 

Содержание 4H42





































Отзывы:

Нет отзывов