Yale 4H42 страница 23 Скачать руководство пользователя

Страница: 23 / 36

5 Inspection and maintenance

LS Open Loop Vector Motor 4H42, 4H71, 4H72 Manual Supplement

za-o.2.8.41-us-1.1

June 2022

Page 23

-o.

-us

-1

The thickness and number of windings of the pressure screws may vary.

It is therefore essential to symmetrically distribute the pressure springs in the coil carrier.

Equip the coil carrier (2) with the correct new pressure spring set.

Place the anchor plate (4) on the coil carrier or compression springs, (observe the

installation position, with size 16 to 60, use fastening screws (1) as a centring aid if

necessary).

10.

Press the anchor plate (4) down against the spring force (e.g. with a spindle press)

and screw in the shoulder screws with the tightening torque specified in the table.

11.

Clean the friction surface of the anchor plate (4) with isopropyl alcohol

so that this is

clear of grease.

12.

For final tasks, see the

Replacing the brake rotor

section.

Hoist motor brake type

Fastening screw (1)

tightening torque

Shoulder screws (5)

[Nm]

RSM 16

9.0

2.0

RSM 32

3.5

RSM 60

22.0

5.6

Replacing the hub

Remove the brake rotor, see the

Replacing the brake rotor

section.

(11)  Hub
(12)  Retaining ring
(13)  Retaining ring
(14)  Motor shaft

Remove the retaining ring (13).

Pull the hub (11) off the motor shaft (14).

Put on a new retaining ring (12). Ensure that the retaining ring engages in the groove.

Push the new hub (11) onto the motor shaft (14).
–

The turned side of the hub (11) must point towards the end of the motor shaft.

–

The new hub (11) must rest against the inner retaining ring (12) so that the outer

retaining ring (13) can be fitted.

Mount the retaining ring (13). Ensure that the retaining ring engages in the groove.

Install the brake rotor, see the

Replacing the brake rotor

section.

Содержание 4H42





































Результаты поиска

Содержание 4H42

Отзывы:

Похожие инструкции для 4H42

Бренды по названию

Популярные бренды

Yale 4H42, Руководство пользователя

Результаты поиска

Содержание 4H42

Отзывы:

Похожие инструкции для 4H42

Бренды по названию

Популярные бренды