Yaesu FTM-6000R Скачать руководство пользователя страница 4

Страница: 4 / 37

Basic Operation

Microphone Gain Setting

The microphone gain has been programmed at the factory to a level that should be sat-

isfactory for the supplied SSM-85D Microphone. If an after-market microphone is used,

you may wish to set a different Mic Gain level.
1. Press and hold the [

menu

] key.

2. Rotate the

DIAL

knob to select [

13 MIC.GAIN

] then

press the

DIAL

knob.

3. Rotate the

DIAL

knob to select the desired setting.

The microphone gain level can be selected from 5

levels.

MIN / LOW / NORMAL / HIGH / MAX

Default:

NORMAL

4. Press the

DIAL

knob to save the setting and return to normal operation.

Setting the volume of the beep

Adjust the volume of the beep that sounds when a key is pressed.
1. Press and hold the [

menu

] key.

2. Rotate the

DIAL

knob to select [

05 BEEP

] then

press the

DIAL

knob.

3. Press the

DIAL

knob to select the desired setting.

The Beep volume can be selected from 3 levels.

OFF / LOW / HIGH

Default:

LOW

4. Press the

DIAL

knob to save the setting and return to normal operation.

Содержание FTM-6000R






































Результаты поиска

Содержание FTM-6000R

Отзывы:

Похожие инструкции для FTM-6000R

Бренды по названию

Популярные бренды

Yaesu FTM-6000R, Руководство для продвинутых пользователей

Результаты поиска

Содержание FTM-6000R

Отзывы:

Похожие инструкции для FTM-6000R

Бренды по названию

Популярные бренды