Yaesu FTM-200DR Скачать руководство пользователя страница 59

Страница: 59 / 67

MAIN BAND

The main band will be selected.

SUB BAND

The sub-band will be selected.

A-BAND FIX The upper band will be selected.

B-BAND FIX

The lower band will be selected.

68 DATA SPEED

Set the baud rate of the APRS (internal modem), and the data communication (when

using the DATA jack at the back of the main body.
1. Press and hold the [

MENU

] key



[

68 DATA SPEED

]



Press the

DIAL

knob

The screen for the detailed settings will be displayed.

APRS

Sets the APRS packet communication speed.
1. Rotate the

DIAL

knob to select [

APRS

] then press the

DIAL

knob.

2. Rotate the

DIAL

to select the APRS communication speed, then press the

DIAL

knob.

The setting switches as follows:

1200 bps

/ 9600 bps

DATA

Sets the APRS data communication speed.
1. Rotate the

DIAL

knob to select [

DATA

] then press the

DIAL

knob.

2. Rotate the

DIAL

to select the data communication speed, then press the

DIAL

knob.

The setting switches as follows:

1200 bps

/ 9600 bps

69 DATA SQL

Sets the output status (during transmission) of the

PK SQL (squelch control)

terminal

(6 pin)

on the DATA Jack.

1. Press and hold the [

MENU

] key



[

69 DATA SQL

]



Press the

DIAL

knob

2. Rotate the

DIAL

knob to select the desired setting.

TX ON

The SQL terminal becomes active during transmission.

TX OFF

The SQL terminal does not become active during trans-

mission.

• The action to be taken when the receive band specified using [DATA] under “67

DATA BAND” in the DATA set-up menu is ready to transmit is set here.

• When this is set to ON, transmissions of external devices such as TNC can be

suppressed.

APRS

The APRS of the transceiver is a communication system for data such as messages and

station positions using the APRS format. Refer to the separate Operating Manual APRS

Edition for details (download the manual from the YAESU website).

Содержание FTM-200DR




































































Результаты поиска

Содержание FTM-200DR

Отзывы:

Похожие инструкции для FTM-200DR

Бренды по названию

Популярные бренды

Yaesu FTM-200DR, Руководство для продвинутых пользователей

Результаты поиска

Содержание FTM-200DR

Отзывы:

Похожие инструкции для FTM-200DR

Бренды по названию

Популярные бренды