Yaesu FT-991A Скачать руководство пользователя

Страница: 63 / 158

Page 61

FT-

991

Operating Manual

1. Press the

BAND

button to show the band list, and

then touch a band key corresponding to the Amateur

band on which you wish to operate.

2. Press the

MODE

button to show the mode list, and

then select the operating mode by touching the cor-

responding key.

Advice:

By convention, LSB is used in the 7 MHz and lower

Amateur bands for SSB communication, and USB is

used on the 14 MHz and higher bands (the 10 MHz

band is used for CW and data modes only).

3. Rotate the Main Tuning Dial knob to adjust the op-

erating frequency. Alternately, you may use the

DWN

scanning buttons on the

MH-31

A8J

Hand Mi-

crophone to scan up or down the current band.

4. Press the microphone

PTT

(Push To Talk) switch to

begin transmitting; speak into the microphone in a

normal voice level.

Advice:



The “

” indicator will light up in the TFT LED

indicators area, confirming that transmission is in

progress.



When transmitting in the AM mode, set a maxi-

mum (carrier) power output of 25 Watts by press-

ing [

RF PWR

], then rotate the

MULTI

knob.

5. Adjust the microphone amplifier gain to match the

microphone and your voice level: Touch [

METER

]

on the LCD repeatedly to select the “

ALC

”.

Press and hold the

PTT

switch, and speak into the

microphone in a normal voice level.

In the SSB mode

, touch [

MIC GAIN

] and then ad-

just

MULTI

knob so that the ALC meter stays within

the ALC zone of the meter (

up to half scale deflec

tion) on voice peaks.

SSB/

AM Mode Transmission

ON/OFF Switch

Main Tuning Dial Knob

F(M-LIST) Button

MULTI Knob

MODE Button

BAND Button

In the AM mode

, touch [

MIC GAIN

] and then adjust

the

MULTI

knob so that the ALC meter does not de-

flect on voice peaks.



When transmitting In the AM mode, adjust the

MIC gain so that the PO meter does not deflect

when speaking.

6. Release the

PTT

switch at the end of the transmis-

sion. The transceiver will return to the receive mode.

Содержание FT-991A































































































































































Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды

Yaesu FT-991A, Руководство по эксплуатации

Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды