Yaesu FT-991A страница 152 Скачать руководство пользователя

Страница: 152 / 158

Page 150

FT-

991

Operating Manual

A/B Button ................................................................. 22

A=B Button ................................................................ 22

About ATU Memories ................................................ 64

About ATU Operation ................................................ 64

About Coaxial Cable .................................................. 13

About GPS Positioning ............................................ 116

About the Display ...................................................... 24

Accessories & Options ................................................. 7

Active-Tuning Antenna System (ATAS-120A) ....... 145

Adjustable Receiver Audio Filter ............................... 60

Adjusting the Clock ................................................... 10

Adjusting the Main Tuning Dial Torque ...................... 9

Adjusting the Noise Blanker Level ............................ 49

Adjusting the SSB Transmitted Bandwidth ............... 69

AF GAIN Knob.......................................................... 23

AGC ........................................................................... 59

Alaska Emergency Frequency: 5167.5 khz.............. 112

A>M Button ............................................................... 23

AM Mode Transmission ............................................ 61

AMS (Automatic Mode Select) Operation ................ 40

Antenna Considerations ............................................. 13

ANT Jack (144/430MHz) .......................................... 27

ANT Jack (HF/50MHz) ............................................. 28

ARS ............................................................................ 95

ATAS-120A .............................................................. 145

ATT (Attenuator)........................................................ 47

Attenuator .................................................................. 47

ATU Operation ........................................................... 63

Audio Peak Filter ....................................................... 58

Automatic Gain Control ............................................. 59

Automatic Mode Select .............................................. 40

Automatic Repeater Shift (ARS) ............................... 95

Available Options ......................................................... 8

BAND Button ............................................................ 21

Band Stack Operation ................................................ 39

Base Station Wire Stand ............................................... 9

Basic Operation .......................................................... 32

Before You Begin ......................................................... 9

C4FM Mode (Digital Mode) Operation ..................... 97

Changing the Frequency of the Home Channel ....... 105

Checking a Memory Channel Status ........................ 107

Choosing the Desired Memory Group ...................... 111

CLAR Button ............................................................. 23

CLAR (Clarifier) Operation

....................................... 36

Clarifier Operation

..................................................... 25

CLAR/VFO-B Knob .................................................. 23

Clock .......................................................................... 25

Connection of Antenna and Power Cables ................. 15

Connection of Headphone .......................................... 16

Connection of Microphone ........................................ 16

Connection of Remote Control Keypad ..................... 16

Contest Memory Keyer .............................................. 86

Contest Number Programming .................................. 87

CONTOUR Control ................................................... 50

Convenient Memory functions ................................ 103

C.S Button .................................................................. 22

C.S (Custom Switch) ................................................. 39

Current Mode (Modulation Form) Indicator .............. 24

Custom Switch ........................................................... 39

CW Convenience Features ......................................... 84

CW Delay Time Setting ............................................. 85

CW Pitch Adjustment................................................. 85

CW Spotting (Zero-Beating) ...................................... 84

DATA (PSK) Operation ........................................... 122

DC IN Jack ................................................................. 27

DG-ID/DP-ID Features .............................................. 99

Digital Group ID (DG-ID) feature ............................. 99

Digital Mode Operation ............................................. 97

Digital Noise Reduction (DNR) ................................. 56

Digital NOTCH Filter (DNF) .................................... 56

Digital Personal ID (DP-ID) feature ........................ 101

DIMMER ................................................................... 37

Displaying the Position Information ........................ 118

DNF............................................................................ 56

DNR ........................................................................... 56

Electronic Keyer ........................................................ 80

Enhancing Transmit Signal Quality ........................... 65

Entering the Location Information Manually .......... 118

Erasing Memory Channel Data ................................ 107

EXT SPKR Jack ......................................................... 28

FAST Button .............................................................. 23

FAST Indicators ......................................................... 26

FC-40 External Automatic Antenna Tuner .............. 143

FH-2 Remote Control Switches ................................. 30

F(M-LIST) Button ..................................................... 21

FM Mode Operation .................................................. 93

Front Panel Controls & Switches ............................... 20

Full Reset ................................................................... 12

Full Reset (Except SETUP settings) .......................... 12

Function Menu ........................................................... 25

General Description ..................................................... 1

GM Function ............................................................ 119

GND ........................................................................... 27

GPS/CAT Jack ........................................................... 27

GPS Function ........................................................... 116

GPS Signal Capturing Indicator ................................. 25

Grounding .................................................................. 14

HI-SWR Indicator ...................................................... 24

Home Channel ......................................................... 105

Index

Содержание FT-991A































































































































































Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды

Yaesu FT-991A, Руководство по эксплуатации

Результаты поиска

Содержание FT-991A

Отзывы:

Похожие инструкции для FT-991A

Бренды по названию

Популярные бренды