Yaesu FT-818ND Скачать руководство пользователя страница 70

Страница: 70 / 76

Installation of Optional Accessories

Optional Filters YF-122S/YF-122C/YF-122CN

1. Turn the transceiver’s power off by pressing and holding in the

switch for 1/2 sec-

ond, then remove the

FBA-28

Battery Case or

SBR-32MH

Ni-MH Battery Pack from

the transceiver. Additionally, disconnect the DC cable from the

INPUT: 13.8V

jack on

the rear panel of the transceiver, when operating the

FT-818

with a DC power supply.

2. Referring to Figure 1, remove the shoulder belt bracket and its two screws from both

side of the transceiver, then remove the five screws affixing the top case of the trans

ceiver, and remove the top case; disconnect the speaker’s connector when you remove
the top case.

Refer to Figure 2 for the mounting locations for the optional filters. Position the filter so

that its connectors are aligned with the mounting pins on the board, and push it into
place.

4. Replace the top case (remember to replace the internal speaker’s plug), and connect

the

FBA-28

Battery Case or

SBR-32MH

Ni-MH Battery Pack (and/or attach the DC

power supply), and turn the transceiver on by pressing and holding in the

switch.

5. Change the setting of Menu #38 (OP FILTER) to “SSB” (if installing the YF-122S), or “CW”

(for the YF-122C/YF-122CN).

6. Filter installation is now complete.

BAND

DWN

MODE







Figure 1

BAND

DWN

MODE

YF-122S/YF-122C/YF-122CN

Mounting Location

Speaker's Connector



Optional Filter

MAIN Unit

Figure 2

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды