background image

FT-65

R

/FT-65

E

Quick Manual

Speaker

V/M key

Microphone

LED Flash-Light

LCD (Liquid Crystal Display)



 key

Quick Recall key

BAND key

Alphabet / Numeric keys

0 / zero-set key

*The circled numbers in the table correspond to the circled numbers 

in the procedures of this manual.

Basic Operation

Turn the Power ON and OFF

Rotate the 

PWR/VOL

 knob out of the click-stop to turn the transceiver 

ON. The current DC supply voltage will be shown on the display for two 

seconds. After the two second interval, the display will commence the 

normal operating frequency indication.

Changing between VFO mode and Memory mode

Press the  [

V/M

] key repeatedly to toggle the frequency control between 

the VFO mode and the Memory mode.

For details on Memory channels, see “Setting the Memory Channels“ on the 

back page.

Selecting the Operating Band

Press the  [

#BAND

] key repeatedly to change the operating frequency 

between the 144 MHz Band, the 430 MHz Band, and the 95 MHz (FM 

Radio Broadcast) Band. Frequency ranges are shown in the table.

Frequency Range (MHz)

RX

TX

RX

TX

USA version

136-174

144-148

400-480

430-450

EU version

136-174

144-146

400-480

430-440

Asian version

136-174

136-174

400-480

400-480

Frequency Navigation

1.Tuning Frequency

Pressing the  [

] key tunes the 

FT-65R/E

 toward a higher frequency, 

while pressing the  [

] key will lower the operating frequency, in steps 

preprogrammed for the current operating band.

2.Direct Keypad Frequency Entry

The operating frequency may be entered directly from the keypad by 

pressing the numbered digits on the keypad in the proper sequence.

Example:

To enter 145.000 MHz*, press [1] 

 [4] 

 [5] 

 [0] 

 [0] 

 [0]

*There is a short-cut to enter frequencies ending in zeros - after the last non-

zero digit, press and hold the    to enter the remaining zeros.

3.Scanning
Manual VFO Scan:

To manually initiate VFO scanning, press and hold either the  [

] or  [

key to begin upward or downward scanning, respectively.

Programmed Mode VFO Scan:

To begin scanning within a limited sub-band range from the VFO mode, 

press and hold the  [

#BAND

] key to select the bandwidth for the 

Programmed Mode (VFO) scanner. Then press the 

F

 key and the 

[

#BAND

] key to start scanning.

Transmission

To transmit, press the 

PTT

 switch, and speak into the front panel 

microphone (located in the lower left-hand corner of the speaker grille) 

in a normal voice level. The 

TX/BUSY

 indicator will glow red during 

transmission.

Activating the Set Mode

Use the following procedure to activate the Set Mode and configure the 

transceiver parameters.

1.   Press and hold the 

key to enter the Set mode.

2.   Repeatedly press the  [▲] or  [▼] key to select the Set Mode Item to be adjusted.

3.   Press  the 

key momentarily to enable adjustment of the Set Mode Item.

4.   Press  the 

[▲] or  [▼] key to adjust the level, or choose the parameter, of the 

selected Set Mode Item.

5.   After completing the selection and adjustment, press the 

PTT 

switch to save the new 

setting and exit to normal operation.

Antenna Jack

TX/BUSY Indicator Lamp

EMERGENCY Key

PWR/VOL Knob

PTT (Push To Talk) Switch

F key

MONI/T.CALL Key

(Function is selectable from Set mode)

SP Jack
MIC Jack

EH066M551

Отзывы: