Xylem Sontek River Surveyor RS5 Скачать руководство пользователя страница 141

Страница: 141 / 149

SonTek RS5 User Manual (August 2020) 141

Appendix D. How to Enable External GNSS using the GNSS

Unlock Code

The GNSS/GPS unlock and configuration operations can be found through Tools >

Hardware Utilities > Instrument Options. Please note that the RS5 system must be

connected to see these options. The Instrument Options dialog is shown below:

If the user has upgraded their RS5-Basic system to RS5-Max, they will need to first use

the unlock code provided by SonTek to enable the GNSS/GPS capabilities of the Max

system. Please note that the following steps do not need to be performed if the user has

purchased a Max system directly from SonTek, as these steps will already have been

configured.

The instrument unlock code is an 8-digit alpha-numeric code specific to each RS5

system. Enter the code into the space in the “Enable GNSS” line and press Apply Code.

If the code is entered properly, the following message will appear:

The user will also see that the GNSS feature has been enabled:

Содержание Sontek River Surveyor RS5






















































































































































Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды

Xylem Sontek River Surveyor RS5, Руководство пользователя

Результаты поиска

Содержание Sontek River Surveyor RS5

Отзывы:

Похожие инструкции для Sontek River Surveyor RS5

Бренды по названию

Популярные бренды