Xylem sensus AutoRead Скачать руководство пользователя

Страница: 129 / 161

Most Commonly Used Functions

FUNCTION

MUST BE

PERFORMED FROM

THIS STATUS

DESCRIPTION

Clear

Any

Clears the selected route

of any route or reading

data.

Import

No Meters (Data: Not

Loaded)

Imports the route data

from the route file created

by the billing software.

Load Data

Ready to Load (Data: Not

Loaded)

Loads the route data

to the Reading Device,

preparing it for use by the

meter reader.

Read Data

Device Loaded (Data:

Loaded)

Copies the reading data

from the Reading Device,

generates an export file

with readings, and prints

the meter reading reports.

Backup

Any

Backs up the current

route data to the specified

location.

What does "Invalid Operation-Multi" mean?

This message means that the Device that you are trying to Read or Clear was last loaded

with multiple routes, and you are not selecting all of those routes when you are trying to

process the device. Check the Status column for all the routes assigned to the device

you are trying to process, and see if there are any other routes for the device that show a

status of Device Loaded (Data: Loaded). If there are other routes in Device Loaded (Data:

Loaded) status for the same device, you must select ALL the routes that you had originally

loaded before you can proceed. AutoRead gives this error as a protective measure. It is

attempting to prevent you from forgetting about other routes you have on the device, and

potentially losing readings. Please refer to the section on loading multiple routes below for

more information.

How do I load multiple routes on my HHD?

There may be times when you wish to load more than one route into the HHD at one time.

In AutoRead, each line in the Process Routes screen is considered a "route." Your routes

may be named after the device (HHD001 or SSI001) or they may have more specific names

(Route 1, East Side, Book 1, etc). One thing to consider about loading multiple routes to a

HHD is that they all must be assigned to the same

Device ID

Appendix A: Frequently Asked Questions | 129

Содержание sensus AutoRead


































































































































































Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды

Xylem sensus AutoRead, Руководство пользователя

Результаты поиска

Содержание sensus AutoRead

Отзывы:

Похожие инструкции для sensus AutoRead

Бренды по названию

Популярные бренды