Xylem ProSwap 610224-01 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 116

Xylem ProSwap 610224-01 Скачать руководство пользователя страница 83

83

5.5

File Menu

Import

Users can import various files transferred from previous versions of KorEXO and KorDSS Software or from other instances of Kor
Software installed on different computers. These files may be transferred remotely through email or manually using a USB flash
drive. Take note of which folder the file is transferred to on the computer.

IMPORT CALIBRATION

– Allows users to import calibration files from another instance of Kor Software.

Compatible files will have the “.cal or .xml” extension.

IMPORT DEPLOYMENT

– Allows users to import deployment templates from another instance of Kor Software.

Compatible files will have the “.dep or .xml” extension.

IMPORT EXO BINARY FILE

– Allows users to import data files from another instance of Kor Software.

Compatible files will have the “.bin” extension.

IMPORT SITE

– Allows users to import sites created from an older version of Kor Software.

Compatible files will have the “.sit” extension.

Settings

Users can adjust general settings related to the software as well as parameter specific settings. It is important to note that these
settings are saved locally and only pertain to the software itself. These settings are not pushed to any instruments nor are they
carried over to instances of Kor Software installed on other computers.

General Settings

AUTOMATION SETTINGS

• Automatically Update Software and Firmware – Toggle On/Off

The software will indicate if there is an update available. An internet connection is required to check for software
and firmware updates.

• Automatically Connect to Instrument – Toggle On/Off

The instrument will automatically connect as soon as it is discovered by the Instrument Connection Panel.

• Automatically Download Data from Instrument to PC – Toggle On/Off

Upon connection to the instrument, it will automatically download any new data that has been collected since it was last
connected to the software.

• Automatically Update Instrument Time to PC Time – Toggle On/Off

The software will update the instrument clock to sync with the PC time.

The File Menu allows users to view software information and adjust software-specific settings.

•  Import
•  Settings
•  About
•  Exit

Kor Software

«
...
81
82
83
84
85
...
»

Содержание ProSwap 610224-01





















































































































Отзывы:

Нет отзывов