Xylem Flygt 2620.172 Скачать руководство пользователя страница 67

Страница: 67 / 72

6 Technical Reference

6.1 Application limits

Data

Description

Media (liquid) temperature

Maximum 40°C (104°F)
Standard version option, Warm media (liquid) version:

Maximum temperature 70°C (158°F).
Warm liquid has certain operational limitations, which

are stated on a plate on the pump.

pH of the pumped media (liquid)

5–8

Media (liquid) density

1100 kg/m³ (9.2 lb per US gal) maximum

Depth of immersion

Maximum 20 m (65 ft)

Maximum permissible working pressure

2.8 bar (40.6 psi)

Other

For the specific weight, current, voltage, power ratings,

and speed of the pump, see the data plate of the pump.
For other applications, contact a sales or authorized

service representative for information.

6.2 Motor data

Feature

Description

Motor type

Squirrel-cage induction motor

Frequency

Standard version: 50 or 60 Hz
MSHA version: 60 Hz

Supply

1-phase or 3-phase

Starting method

Direct on-line

Maximum starts per hour 30 evenly-spaced starts per hour
Code compliance

IEC 60034-1

Voltage variation without

overheating

±10%, if it does not run continuously at full load

Voltage imbalance

tolerance

Stator insulation class

F (155°C [311°F])

Motor encapsulation

Motor encapsulation is in accordance with IP68.

6.3 Specific motor data

1-phase, 50 Hz

Motor type:

• 2,830 rpm
• 1.5 kW (2.0 hp)

Voltage, V

Rated current, A

Starting current, A

Power factor, cos

220

8.7

0.99

230

8.4

0.98

240

8.3

0.96

6 Technical Reference

2620.172/.281 Service and Repair Instructions

Содержание Flygt 2620.172









































































Результаты поиска

Содержание Flygt 2620.172

Отзывы:

Похожие инструкции для Flygt 2620.172

Бренды по названию

Популярные бренды

Xylem Flygt 2620.172, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание Flygt 2620.172

Отзывы:

Похожие инструкции для Flygt 2620.172

Бренды по названию

Популярные бренды