manualshive.com logo in svg

Xylem Flygt 2008 Ready 8, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem Flygt 2008 Ready 8 Скачать руководство пользователя страница 10

3  Product Description

3.1  Products included

Pump model

Standard

EX

MSHA

Drainage

Sludge

Ready 8, 2008.212

X

X

Ready 8S, 2008.281

X

X

3.2  Pump design

The pump is submersible, and driven by an electric motor.

Intended use

The product is intended for moving waste water, sludge, raw and clean water. Always
follow the limits given in 

Technical Reference

 on page 36. If there is a question regarding

the intended use of the equipment, then contact a sales or authorized service
representative before proceeding.

DANGER: Explosion/Fire Hazard

Special rules apply to installations in explosive or flammable atmospheres. Do not install
the product or any auxiliary equipment in an explosive zone unless it is rated explosion-
proof or intrinsically-safe. If the product is EN/ATEX-, MSHA- or FM-approved, then see
the specific EX information in the Safety chapter before taking any further actions.

For information about pH, see 

Technical Reference

 on page 36.

Particle size

Version code 281: The pump can handle liquid containing particles that correspond to
the pump housing inlet. The diameter of the pump housing inlet is 38 mm (1.5 in).
Version code 212: The pump can handle liquid containing particles that correspond to
the holes in the strainer.

Number of holes

Hole dimensions

Version code 212: 96

11×5 mm (0.43×0.2 in)

Pressure class

MT

Medium head

Impeller type

Version code 212: B

Wear resistant

Version code 281: D

Sludge

3.3  Monitoring equipment

The following applies to the monitoring equipment of the pump:

• The stator incorporates thermal contacts connected in series that activate the alarm at

overtemperature.

• The thermal contacts open at 135°C (275°F).

3.3.1  Level regulators

About level regulators

Starting and stopping the pump at different water levels can be manual or automatic. If
automatic start and stop is required, a level regulator can be ordered (as an option). The
option is only available for standard pumps.

3  Product Description

8

2008 Ready 8, 8S Installation, Operation, and Maintenance

Содержание Flygt 2008 Ready 8













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды