Xylem FLYFT P7900 Скачать руководство пользователя страница 10

Страница: 10 / 76

WS013648A

2. Lift the pump by using the correct lifting equipment.
3. Put the pump upright on a rigid horizontal surface so that it cannot fall over.
4. Cut the transportation strap.

WS013649A

2.3 Temperature ranges for transportation, handling and storage

Handling at freezing temperature

At temperatures below freezing, the product and all installation equipment, including the

lifting gear, must be handled with extreme care.
Make sure that the product is warmed up to a temperature above the freezing point before

starting up. Avoid rotating the impeller/propeller by hand at temperatures below the freezing

point. The recommended method to warm the unit up is to submerge it in the liquid which will

be pumped or mixed.

NOTICE:
Never use a naked flame to thaw the unit.

2 Transportation and Storage

P7900 Installation, Operation, and Maintenance Manual

Содержание FLYFT P7900













































































Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды

Xylem FLYFT P7900, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FLYFT P7900

Отзывы:

Похожие инструкции для FLYFT P7900

Бренды по названию

Популярные бренды