background image

Page: 9 

Mounting and Connecting tips 

 

Mounting alternatives 

 

 

  

Normally the XTZ 99.38 MKII is placed standing by a 
wall. The wall behind and besides the loudspeaker have 
influence both on the bass level and the bass 
characteristics, so please be patient and try different 
distances to the rear and side walls.

 

     

 

Connect 

using 

the 

correct phase 

 

 

  Always  connect  using  the  correct  phase,  from  the 

+-pole  on  the  amplifier  to  the  +-pole  on  the 

loudspeaker and corresponding for minus (-). 
 

   

If  you by  accident  connect  the  other  way, 
there  is  no  risk  of  damage.  However,  the 
sound will not be correct, especially in the 

lower frequencies. 
 

 

Overload

 

 

 

  At high load during extensive time periods, there is 

always  the  risk  of  overloading  the  driver  and 

amplifier. 

 

   

All  loudspeakers  have  a  limited  patience 

for  high  power,  so  be  careful  not  to  play 
extremely  loud  and  not  to  increase  treble 
or bass settings too much.

 

By increasing the bass or treble from 0 to 

max you will increase the power by about 
16 times. 

 

The initial playing time 

 

 

  

It takes about 50 to 100 hour of initial playing time, for 
the driver to sound optimal. During this time, the 
speaker may be used normally.

 

 

     

 

Overload

 

 

 

  When  the  active  input  is  used,  there  is  no  passive 

filtering of the woofer.  

 

If  bi-  or  tri-amping  is  used,  the  metal  connection 

must be removed between the terminals.  

   

OBS! 
Damage  on  the  speaker  caused  by 
incorrectly  connected  filter  is  NOT 
covered by the warranty.  

Be  therefore  careful  when  you  plug  in 
speakers. 

 

Содержание 99.38 Mk II














Отзывы: