Xtralis VESDA LCD Programmer Hand Held Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 54

background image

Xtralis VESDA LCD Programmer Product Guide

Xtralis

VESDA

®

6

www.xtralis.com

Table 1 - LCD Programmer specifications

The LCD Programmer Keys

The LCD Programmer has two rows of keys. The keys are used to move the cursor and to use
the various functions of the LCD Programmer.

The top row of keys have dual functions and are known as “Soft Keys”. When the commands
NO, BACK, YES, CONT, EXIT, QUIT, or WAIT are

displayed on the LCD screen, the soft key

directly below the command actions the respective command.

The bottom row are the “Hard Keys”. Each hard key has a single function. The function of the
LCD Programmer keys are mentioned in Table 3,

“Description of LCD Programmer keys and

functions”

on page 8.

Figure 3 - LCD Programmer keys

4

User Access Levels and PIN

User Access Level

The three user access levels allow different people to access different sets of functions. The
functions that can be edited with USR, ADM and DST access levels are listed in

Programmer Screen Description

Table 2 - User access levels

Connections:

Terminal Connector
to Head Processor
Card or to
expansion
connector on
another Xtralis
VESDA device.

15 pin D-type
connector.
VESDAnet cable
required. Connects
to Detector or
Remote
VESDAnet Socket.

RS485 VESDAnet
field wiring to
screw terminals
blocks (0.2 - 2.5
mm, 30 - 12 AWG

User
Level

Access
Level

Functional Authorization

USR

Low

This is the USER or the OPERATOR level. The
user can view the event log, change the date
and the time. They can also perform selected
VESDA Zone control functions.

ADM

High

At the ADMINISTRATOR level access is
available to most functions. These include
setting alarm thresholds, normalizing air flows,
and defining the relay Configuration.

DST

Absolute

The DISTRIBUTOR level allows unlimited
access to all the system commands and
parameters.

Legend

B

Soft Keys

C

Hard Keys

«
...
10
11
12
13
14
...
»

Содержание LCD Programmer Hand Held























































Отзывы:

Нет отзывов

Похожие инструкции для LCD Programmer Hand Held

Virtex-II Pro ML300

Бренд: Xilinx Страницы: 17

Бренд: ASROCK Страницы: 6

Бренд: JETWAY Страницы: 52

PP-I7RS400 PURE PERFORMANCE II

Бренд: Sapphire Audio Страницы: 44

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Бренд: ASROCK Страницы: 154

Z690M DS3H DDR4

Бренд: Gigabyte Страницы: 36

Бренд: JETWAY Страницы: 37

Бренд: Avalue Technology Страницы: 116

Бренд: XMOS Страницы: 20

Бренд: Broadcom Страницы: 20

Бренд: MSI Страницы: 75

Бренд: MSI Страницы: 445

XtremeDSP Spartan-3A DSP 3400A...

Бренд: Xilinx Страницы: 50

FIERCE 2 54LB/48

Бренд: Watersnake Страницы: 44

Venom SXW 34/26

Бренд: Watersnake Страницы: 44

ADVANCE SWS 70/36

Бренд: Watersnake Страницы: 28

Бренд: Asus Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды