manualshive.com logo in svg

XIMEA xiC, Техническое руководство

Поделиться
Скачать
XIMEA xiC Скачать руководство пользователя страница 80

 

 

xiC - Technical Manual Version 1.16 

 

80

 

 

4.3.2.2.

 

Triggered acquisition - burst of frames 

Frame Burst Start 

In this mode each trigger pulse triggers defined number of exposed frames.  

 

figure 4-5, triggered burst of frames – frame burst start, number of frames in burst set to 3 

 

Frame Burst Active 

If trigger is level sensitive it can be used to control image acquisition. 

 

figure 4-6, triggered burst of frames – frame burst active 

Please see: 

Frame Burst Modes: https://www.ximea.com/support/wiki/allprod/Frame_Burst_Modes

 

4.3.2.3.

 

Exposure defined by trigger pulse length 

In this mode the exposure is defined by trigger pulse length. This can be used to achieve longer exposure than allowed by API. 
Also it can be used to trigger several images in sequence with different exposure time. Exposure time is measured and reported 
in image metadata. 

 

figure 4-7, Exposure defined by trigger pulse length 

Please see: 

Exposure Defined by Trigger Pulse Length: 

https://www.ximea.com/support/wiki/allprod/Exposure_Defined_by_Trigger_Pulse_Length 

 

 

 

Содержание xiC






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды