XIMEA xiC Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 117

background image

xiC - Technical Manual Version 1.16

55

3.10.

xiC Digital Input / Output (GPIO) Interface

USB XiC cameras use the 8-pin connector for the GPIO interface and external power supply (AUX) connection and have multiple
options for inputs and outputs. The flex line cameras have one input and one output available through the flex line (see pin-out
above).

Connector

Signals

Mating Connectors

I/O & Sync 8-pin Opto-isolated trigger input and non-isolated I/O

Binder 8-pin PN: 79 1426 15 08

Flex cable

One input and one output non-isolated

table 3-30, GPIO mating connector description

3.10.1.

Location

IO interface receptacle (for USB cameras only) is located on the back of the camera:

figure 3-43, position GPIO connector

3.10.2.

IO Connector Pinning

Pinning of the IO connector (camera):

figure 3-44, pinning GPIO connector

I/O connector Pin Assignment:

Pin

Name

Signal

Technical description

1

AUX PWR

Power supply input

5V

2

INOUT2

Non-isolated I/O

LVTTL (3V, 50µA)

3

OUT1

Opto- isolated Output 1

Open collector

4

OUT GND

Ground for Opto-Isolated Out (OUT1)

5

IN1

Opto-isolated Input 1

(<0.8V low; 4-24V high)

6

IN GND

Ground for Opto-Isolated Input (IN1)

7

GND

External grounds for power and non-isolated I/O

8

INOUT1

Non-isolated I/O

LVTTL (3V, 50µA)

table 3-31, I/O connector Pin Assignment

xiC

1
2
3
4

MC023CG-SY-UB

CACAU1623001

Made in SK

IO

AUX

power

For use with XIMEA approved connection cables only.

USB 3.1 Gen 1

xiC

1
2
3

4

MC023CG-SY-TC
CACAC1623001

M

ade

in SK

IO

AUX

power

USB 3.1 Gen 1

Type C

8 pin

IO/AUX

connector

1

2

3

4

5

6

7

8

«
...
53
54
55
56
57
...
»

Содержание xiC






















































































































Отзывы:

Нет отзывов

Похожие инструкции для xiC

CAMEDIA C-8080 Wide Zoom

Бренд: Olympus Страницы: 4

CAMEDIA C-730 Ultra Zoom

Бренд: Olympus Страницы: 266

E-20 - Dual Monaural Earphones

Бренд: Olympus Страницы: 2

CAMEDIA E-100 RS

Бренд: Olympus Страницы: 2

Бренд: Xiaoyi Страницы: 30

Бренд: Olympus Страницы: 184

Бренд: 70mai Страницы: 6

Бренд: Baumer Страницы: 68

Бренд: Tamron Страницы: 4

ALIBI ALI-TP3002L

Бренд: Observint Страницы: 6

Бренд: ZENEC Страницы: 2

Бренд: Xview Страницы: 16

Бренд: JENDIGITAL Страницы: 30

200 Series NBC-255-P

Бренд: Bosch Страницы: 94

Predator Hybrid PREDHYB-PSU-SM

Бренд: 360 Vision Страницы: 50

Бренд: Pioneer Страницы: 37

Бренд: Canon Страницы: 71

Бренд: Canon Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды