Xilinx Zynq-7000 Скачать руководство пользователя страница 622

Страница: 622 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

622

UG586 November 30, 2016

www.xilinx.com

Chapter 4:

LPDDR2 SDRAM Memory Interface Solution

Table 4-25:

7 Series FPGA Memory Solution Configuration Parameters

Parameter

Description

Options

REFCLK_FREQ

(1)

This is the reference clock frequency for

IDELAYCTRLs. This can be set to 200.0 for any

speed grade device. For more information, see

the IDELAYE2 (IDELAY) and ODELAYE2

(ODELAY) Attribute Summary table in the

7 Series FPGAs SelectIO™ Resources User

Guide

[Ref 2]

. This parameter should

not

changed.

200.0

SIM_BYPASS_INIT_CAL

(2)

This is the calibration procedure for simulation.

“OFF” is not supported in simulation. “OFF”

must be used for hardware implementations.

“FAST” enables a fast version of read and write

leveling. “SIM_FULL” enables full calibration

but skips the power-up initialization delay.

“SIM_INIT_CAL_FULL” enables full calibration

including the power-up delays.

“OFF”

“FAST”

“SIM_FULL”

nCK_PER_CLK

This is the number of memory clocks per clock.

This parameter should

not

be changed.

nCS_PER_RANK

This is the number of unique CS outputs per

rank for the PHY.

1, 2

DQS_CNT_WIDTH

This is the number of bits required to index the

DQS bus and is given by

ceil(log

(DQS_WIDTH)).

ADDR_WIDTH

This is the memory address bus width. It is

equal to RANK BANK

ROW COL_WIDTH.

BANK_WIDTH

This is the number of memory bank address

bits.

This option is based on the selected

memory device.

CS_WIDTH

This is the number of unique CS outputs to

memory.

This option is based on the selected

MIG tool configuration.

CK_WIDTH

This is the number of CK/CK# outputs to

memory.

This option is based on the selected

MIG tool configuration.

CKE_WIDTH

This is the number of CKE outputs to memory. This option is based on the selected

MIG tool configuration.

COL_WIDTH

This is the number of memory column address

bits.

This option is based on the selected

memory device.

RANK_WIDTH

This is the number of bits required to index the

RANK bus.

This parameter value is 1 for both

Single and Dual rank devices.

ROW_WIDTH

This is the DRAM component address bus

width.

This option is based on the selected

memory device.

DM_WIDTH

This is the number of data mask bits.

DQ_WIDTH/8

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды