Xilinx Vivado MIPI CSI-2 Скачать руководство пользователя страница 64

Страница: 64 / 90

MIPI CSI-2 RX Subsystem v4.0

PG232 July 02, 2019

www.xilinx.com

Chapter 5:

Application Example Design

The MIPI CSI-2 RX Subsystem decodes, processes video data and presents on AXI4-Stream

data with two pixels data per clock. The RAW video data is then converted into RGB data

using the Demosaic IP, V_Gamma_Lut, V_Proc_SS CSC IPs, two pixels at a time.

RGB data is then fed to the Video Test Pattern Generator IP (V-TPG). The TPG is available in

the design to act as an alternate source of video in case no MIPI CSI-2 video source is

present. The TPG (in pass-through mode) sends video packets across the AXI4-Stream data

in dual pixel per beat mode to an AXI4-Stream broadcaster.

The broadcaster is used to broadcast the stream to the MIPI DSI TX Subsystem or HDMI TX

Subsystem to be displayed. The HDMI TX Subsystem is available as an alternative if a MIPI

DSI-compliant display panel is not available. Using the GPIO IP, one of the destination video

paths is selected. The GPIO enables the TREADY signal in the selected path. If the MIPI DSI

TX Subsystem path is chosen, the video is passed through a video processing subsystem

configured as a Scaler. This is required as the MIPI DSI Panel works on a fixed resolution of

1920x1200. All videos must either be up scaled (480p, 720p, 1080p) or downscaled (4K) to

1920x1200 resolution for the MIPI DSI display panel.

The entire system runs at 300 MHz video clock frequency.

Note:

You must have the hardware evaluation license for the following IPs to build the complete

design:

MIPI CSI-2 RX Subsystem

MIPI DSI TX Subsystem

HDMI Subsystem

Test pattern generator

X-Ref Target - Figure 5-1

Figure 5-1:

MIPI CSI-2 Rx Subsystem Application Example Design Block Diagram

Send Feedback

Содержание Vivado MIPI CSI-2



























































































Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Vivado MIPI CSI-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Бренды по названию

Популярные бренды