Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 145

Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 117

Chapter 5

Board Design Guidelines

This chapter presents topics related to implementing a design on a printed circuit board that uses
GTM transceivers. GTM transceivers are analog circuits that require special consideration and
attention when designing and implementing on a printed circuit board. Besides an understanding
of the functionality of the device pins, a design that performs optimally requires attention to
issues such as device interfacing, transmission line impedance and routing, power supply design
filtering and distribution, component selection, and PCB layout and stackup design.

Pin Description and Design Guidelines

The following table defines the GTM transceiver Dual pins.

Table 73: GTM Transceiver Dual Pin Descriptions

Pins

Dir

Description

MGTREFCLKP
MGTREFCLKN

In/Out(Pad)

Configured as either reference clock input pins or as RX recovered

clock output pins for the Dual.

MGTMRXP[1:0]
MGTMRXN[1:0]

In(Pad)

RXP and RXN are the differential input pairs for each of the

receivers in the GTM transceiver Dual.

MGTMTXP[1:0]
MGTMTXN[1:0]

Out(Pad)

TXP and TXN are the differential output pairs for each of the

transceivers in the GTM transceiver Dual.

MGTAVTTRCAL

In(Pad)

Bias current supply for the termination resistor calibration circuit.

Termination Resistor Calibration Circuit

.

MGTRREF

In(Pad)

Calibration resistor input pin for the termination resistor

calibration circuit. See

Termination Resistor Calibration Circuit

MGTAVCC

In(Pad)

MGTAVCC is the analog supply for the internal analog circuits of

the GTM transceiver Dual tile. This includes the analog circuits for

the PLL, transmitters, and receivers. Most packages have multiple

groups of power supply connections in the package for MGTAVCC.

Refer to the package pin definitions to identify the location of the

power supply group for a specific GTM transceiver Dual.The

nominal voltage is 0.9 VDC.

MGTAVTT

In(Pad)

MGTAVTT is the analog supply for the transmitter and receiver

termination circuits of the GTM transceiver Dual tile. Most

packages have multiple groups of power supply connections in the

package for MGTAVTT. Refer to the package pin definitions to

identify the location of the power supply group for a specific GTM

transceiver Dual. The nominal voltage is 1.2 VDC.

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

117

«
...
115
116
117
118
119
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов