manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя

Xilinx Virtex-5 FPGA ML561 - мощный продукт, предлагающий широкие возможности для пользователей. Для удобства пользования, предоставляется User Manual, который можно скачать бесплатно с manualshive.com. Пользователи могут найти подробные инструкции и руководства по использованию продукта для оптимальной производительности.

Поделиться
Скачать
background image

Virtex-5 FPGA User Guide

www.xilinx.com

95

UG190 (v5.0) June 19, 2009

General Usage Description

Phase Shift

In many cases, there needs to be a phase shift between clocks. The phase shift resolution in 
time units is defined as: PS = 1/8 F

VCO

 or D/8MF

IN

 since the VCO can provide eight phase 

shifted clocks at 45° each.

The higher the VCO frequency, the smaller the phase shift resolution. Since the VCO has a 
distinct operating range, it is possible to bound the phase shift resolution using from 
1/8 F

VCO_MIN

 to 1/8 F

VCO_MAX

.

Each output counter is individually programmable allowing each counter to have a 
different phase shift based on the output frequency of the VCO.

Note:

Phase shifts other than 45° are possible. A finer phase shift resolution depends on the output 

duty cycle and 0 value. Consult the architecture wizard for other phase-shift settings.

PLL Programming

Programming of the PLL must follow a set flow to ensure configuration that guarantees 
stability and performance. This section describes how to program the PLL based on certain 
design requirements. A design can be implement in two ways, directly through the GUI 
interface (the PLL Wizard) or directly implementing the PLL through instantiation. 
Regardless of the method selected, the following information is necessary to program the 
PLL:

•

Reference clock period

•

Output clock frequencies (up to six maximum)

•

Output clock duty cycle (default is 50%)

•

Output clock phase shift relative in number of clock cycles relative to the fastest 
output clock.

•

Desired bandwidth of the PLL (default is OPTIMIZED and the bandwidth is chosen 
in software)

•

Compensation mode (automatically determined by the software)

•

Reference clock jitter in UI (i.e., a percentage of the reference clock period)

Determine the Input Frequency

The first step is to determine the input frequency. This allows all possible output 
frequencies to be determined by using the minimum and maximum input frequencies to 
define the D counter range, the VCO operating range to determine the M counter range, 
and the output counter range since it has no restrictions. There can be a very large number 
of frequencies. In the worst case, there will be 52 x 64 x 128 = 425,984 possible 
combinations. In reality, the total number of different frequencies is less since the entire 
range of the M and D counters cannot be realized and there is overlap between the various 
settings. As an example, consider F

IN

= 100 MHz. If the minimum PFD frequency is 

20 MHz, then D can only go from 1 to 5. For D = 1, M can only have values from four to 11. 
If D = 2, M can have values from 8 to 22. In addition, D = 1 M = 4 is a subset of D = 2 M = 8 
allowing the D = 1 M = 4 case to be dropped. For this case, only D = 3, 4, 5, and 7 are 
considered since all other D values are subsets of these cases. 

This drastically reduces the number of possible output frequencies. The output frequencies 
are sequentially selected. The desired output frequency should be checked against the 
possible output frequencies generated. Once the first output frequency is determined, an 
additional constraint can be imposed on the values of M and D. This can further limit the 

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Бренд: Canon Страницы: 32
Rabbit 2000 Reference Manual preview
2000
Бренд: Rabbit Страницы: 120
D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Бренд: D-Link Страницы: 2
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Бренд: D-Link Страницы: 4
dbx Zone Pro 640 Manual preview
Zone Pro 640
Бренд: dbx Страницы: 2
dbx 166 Quick Start Manual preview
166
Бренд: dbx Страницы: 17
Yaesu FT-817 - Modification Instructions preview
FT-817 -
Бренд: Yaesu Страницы: 2
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Бренд: ZALMAN Страницы: 9
axing EOC 1-31 Operation Instructions Manual preview
EOC 1-31
Бренд: axing Страницы: 52
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Бренд: Aewin Technologies Страницы: 86
Omega OMB-DAQBOARD-500 Series User Manual preview
OMB-DAQBOARD-500 Series
Бренд: Omega Страницы: 48
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Бренд: ANEP Страницы: 48
Unex EVK-351 Quick Start Manual preview
EVK-351
Бренд: Unex Страницы: 27
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Бренд: Digital Equipment Страницы: 90
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Бренд: Avigilon Страницы: 12
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Бренд: Microchip Technology Страницы: 41
Netopia D3100-I User Reference Manual preview
D3100-I
Бренд: Netopia Страницы: 138
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Бренд: Variscite Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды