manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, Руководство пользователя

Xilinx Virtex-5 FPGA ML561 - мощный продукт, предлагающий широкие возможности для пользователей. Для удобства пользования, предоставляется User Manual, который можно скачать бесплатно с manualshive.com. Пользователи могут найти подробные инструкции и руководства по использованию продукта для оптимальной производительности.

Поделиться
Скачать
background image

Virtex-5 FPGA User Guide

www.xilinx.com

223

UG190 (v5.0) June 19, 2009

SelectIO Resources General Guidelines

•

DCI cascading must extend across consecutive banks in the same column. It is not 
possible to skip banks when using DCI cascading. For example, consider four banks 
in a column A, B, C, and D, from top to bottom. In this case, the following are valid 
possibilities for DCI cascading, assuming all other guidelines are met:

♦

DCI cascading can extend to Bank A, Bank C, or both banks.

♦

DCI cascading can also extend to Bank D, since Bank D is in the same column. 
However, DCI cascading must also extend to the intervening Bank C. If DCI I/O 
standards are implemented in Bank C, DCI I/O banking compatibility must be 
observed across all three banks (B, C, and D).

•

DCI cascading can span the entire column as long as the above guidelines are met. 

•

Locate adjacent banks. Bank location information is best determined from partgen 
generated package files (

partgen -v XC5VLX50TFF1136

). The resulting package 

file with a .pkg extension contains XY I/O location information. The X designator 
indicates I/Os in the same column. The Y designator indicates the position of an I/O 
within a specific bank. The bank number is also shown. Consecutive Y locations 
across bank boundaries show adjacent banks. For example, the XC5VLXT in an 
FF1136 package shows bank 11 starting with I/O X0Y159 end ending with I/O 
location X0Y120. Bank 13 starts with I/O X0Y119 and ends with X0Y80. Bank 15 starts 
with X0Y199 and ends with X0Y160. This indicates that bank 13 is to the south of bank 
11, and bank 15 is to the north. As the Y coordinates of these two banks are 
consecutive, these two banks are considered consecutive banks and can be DCI 
cascaded. It is possible to cascade through an unbonded bank.

•

DCI cascade is enabled by using the DCI_CASCADE constraint described in the 
constraints guide.

Xilinx DCI

DCI uses two multi-purpose reference pins in each bank to control the impedance of the 
driver or the parallel termination value for all of the I/Os of that bank. The N reference pin 
(VRN) must be pulled up to V

CCO

 by a reference resistor, and the P reference pin (VRP) 

must be pulled down to ground by another reference resistor. The value of each reference 
resistor should be equal to the characteristic impedance of the PC board traces, or should 
be twice that value. See 

“Driver with Termination to V

CCO

/2 (Split Termination),” page 

228

.

When a DCI I/O standard is used on a particular bank, the two multi-purpose reference 
pins cannot be used as regular I/Os. However, if DCI I/O standards are not used in the 
bank, these pins are available as regular I/O pins. The 

Virtex-5 Family Packaging 

Specifications 

gives detailed pin descriptions. 

DCI adjusts the impedance of the I/O by selectively turning transistors in the I/Os on or 
off. The impedance is adjusted to match the external reference resistors. The impedance 
adjustment process has two phases. The first phase compensates for process variations by 
controlling the larger transistors in the I/Os. It occurs during the device startup sequence. 
The second phase maintains the impedance in response to temperature and supply voltage 
changes by controlling the smaller transistors in the I/Os. It begins immediately after the 
first phase and continues indefinitely, even while the device is operating. By default, the 
DONE pin does not go High until the first phase of the impedance adjustment process is 
complete. 

The coarse impedance calibration during the first phase of impedance adjustment can be 
invoked after configuration by instantiating the DCIRESET primitive. By toggling the RST 
input to the DCIRESET primitive while the device is operating, the DCI state machine is 

Содержание Virtex-5 FPGA ML561


































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 FPGA ML561

Baicells Nova430i Quick Manual preview
Nova430i
Бренд: Baicells Страницы: 8
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Бренд: Salusfin Страницы: 6
Yamaha DX7mega128 Install Manual preview
DX7mega128
Бренд: Yamaha Страницы: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Бренд: Yamaha Страницы: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Бренд: Yamaha Страницы: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Бренд: Yamaha Страницы: 49
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Бренд: Dahua Страницы: 23
Teac HD-35NAS User Manual preview
HD-35NAS
Бренд: Teac Страницы: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Бренд: Maple Systems Страницы: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Бренд: NETGEAR Страницы: 2
CAP-XX Purpose User Manual preview
Purpose
Бренд: CAP-XX Страницы: 8
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Бренд: Hanwha Techwin Страницы: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Бренд: ZALMAN Страницы: 9
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Бренд: Arbor Technology Страницы: 8
Lattice Semiconductor iCE40 SPRAM Series Technical Note preview
iCE40 SPRAM Series
Бренд: Lattice Semiconductor Страницы: 12
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Бренд: AXIOMTEK Страницы: 2
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Бренд: ADLINK Technology Страницы: 48
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Бренд: A.E.B. Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды