manualshive.com logo in svg

Xilinx T1, Руководство по установке

Поделиться
Скачать
Xilinx T1 Скачать руководство пользователя страница 13

Chapter 3

Installing Additional Software

To run the T1 card skeleton design or other demos provided by Xilinx partners, install the
following additional software on the server:

• DPDK package. The supported versions are 18.11, 19.11, and 20.11.

• DPDK-based pktgen application. The following versions are supported:

○

DPDK 18.11 – pktgen-3.6.1

○

DPDK 19.11 – pktgen-19.12.0

○

DPDK 20.11 – pktgen-21.05.0

Note: For DPDK version 20.11, the DPDG kernel modules are no longer included in the DPDK
package. The dpdk-kmods package is therefore included in the T1 card skeleton design package.

• Application scripts

This software is included in the T1 skeleton design package along with a script to ensure that the
software is installed correctly. The package and the scripts are described in the 

T1 Skeleton

Design Package

 section of this document.

The demos provided by Xilinx partners also contain the additional software. For each design or
demo, there is a local directory for the additional software as well as instructions on building it
for the particular design. There is no central location on the server for these demos.

The software has been tested on the following Linux distributions: Ubuntu 18, Ubuntu 20,
CentOS 7, and CentOS 8.

To run the Xilinx demos, the requirements are as follows:

• Root access is required.

• HugePages is enabled.

Chapter 3: Installing Additional Software

UG1518 (v1.0) December 17, 2021

 

www.xilinx.com

T1 Telco Accelerator Card Installation Guide

 13

Send Feedback

Содержание T1

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды