Xilinx LogiCORE IP AXI Скачать руководство пользователя

Страница: 51 / 107

AXI Bridge for PCI Express v2.4

www.xilinx.com

PG055 June 4, 2014

Chapter 3:

Designing with the Core

Transaction Ordering for PCIe

The AXI Bridge for PCI Express core conforms to strict PCIe transaction ordering rules. See

the PCIe v2.1 Specification

[Ref 5]

for the complete rule set. The following behaviors are

implemented in the AXI Bridge for PCI Express core to enforce the PCIe transaction ordering

rules on the highly-parallel AXI bus of the bridge. The rules are enforced without regard to

the Relaxed Ordering attribute bit within the TLP header:

• The

bresp

to the remote (requesting) AXI4 master device for a write to a remote PCIe

device is not issued until the MemWr TLP transmission is guaranteed to be sent on the

PCIe link before any subsequent TX-transfers.

• A remote AXI master read of a remote PCIe device is not permitted to pass any previous

or simultaneous AXI master writes to a remote PCIe device that occurs previously or at

the same time. Timing is based off the AXI

arvalid

signal timing relative to the AXI

awvalid

. Any AXI write transaction in which

awvalid

was asserted before or at the

same time as the

arvalid

for a read from pcie is asserted causes the MemRd TLP(s) to

be held until the pipelined or simultaneous MemWr TLP(s) have been sent.

• A remote PCIe device read of a remote AXI slave is not permitted to pass any previous

remote PCIe device writes to a remote AXI slave received by the AXI Bridge for PCI

Express core. The AXI read address phase is held until the previous AXI write

transactions have completed and

bresp

has been received for the AXI write

transactions.

• Read completion data received from a remote PCIe device are not permitted to pass

any remote PCIe device writes to a remote AXI slave received by the AXI Bridge for PCI

Express core prior to the read completion data. The

bresp

for the AXI write(s) must be

received before the completion data is presented on the AXI read data channel.

• Read data from a remote AXI slave is not permitted to pass any remote AXI master

writes to a remote PCIe device initiated on the AXI bus prior to or simultaneously with

INCR Burst Read of 32-bit address AXIBAR

MemRd 64 (4DW)

INCR Burst Write to 32-bit address AXIBAR

MemWr 64 (4DW)

Table 3-4:

AXI4-Stream PCIe TLPs to AXI4 Memory Mapped Transactions

AXI4-Stream PCIe TLPs

AXI4 Memory-Mapped Transaction

MemRd 32 (3DW) of PCIEBAR

INCR Burst Read with 32-bit address

MemWr 32 (3DW) to PCIEBAR

INCR Burst Write with 32-bit address

MemRd 64 (4DW) of PCIEBAR

INCR Burst Read with 32-bit address

MemWr 64 (4DW) to PCIEBAR

INCR Burst Write with 32-bit address

Table 3-3:

AXI4 Memory-Mapped Transactions to AXI4-Stream PCIe TLPs

(Cont’d)

AXI4 Memory-Mapped Transaction

AXI4-Stream PCIe TLPs

Send Feedback

Содержание LogiCORE IP AXI












































































































Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды

Xilinx LogiCORE IP AXI, Руководство по эксплуатации продукта

Результаты поиска

Содержание LogiCORE IP AXI

Отзывы:

Похожие инструкции для LogiCORE IP AXI

Бренды по названию

Популярные бренды