Xilinx Kintex-7 FPGA KC705 Скачать руководство пользователя страница 9

Страница: 9 / 24

KC705 Getting Started Guide

www.xilinx.com

UG913 (v3.0.2) April 23, 2013

Introduction

Set the IP address of the host PC to 192.168.1.100. Return the IP address of the PC back
to its original setting after running the demonstration.

Note:

The demonstration uses a hard-coded MAC address and a fixed IP address of 192.16

.1.10

and does not connect to the regular LAN network using DHCP. Do not connect more than one board
to the same network segment.

Running the Video Demonstration

To run the video demonstration, copy and unzip the demonstration package files from the
Web to the host machine and use the following steps:

Note:

Please note that the package has a deep hierarchy structure. So, unzip the package at a user

location such that the overall path length is smaller.

If the KC705 board is not already powered on, plug in the power adapter to local AC
power. Plug the 12V power cable into the board connector on J49. Turn on the power
by switching the SW15 to the ON position.

Open and configure a serial communications terminal utility program with these
settings:

•

Baud Rate:

9600

•

Data:

8 bit

•

Parity:

None

•

Stop:

1 bit

•

Flow Control:

None

Note:

Refer to

Appendix A, Communicating with the KC705 USB-UART

for setting up the

UART communication.

Open a command shell with the Xilinx Design tools environment settings. Refer to

Appendix B, Installation and Licensing of Xilinx Design Tools

for Xilinx tool chain

installation and licensing help.

Note:

To set environment variables, run the

settings32.bat

file located in the Xilinx

installation area. At the command prompt, type

C:\Xilinx\14.x\ISE_DS\settings32.bat

(for Windows XP) or

C:\Xilinx\14.x\ISE_DS\settings64.bat

(for Windows 7) and press

Enter

Go to the unzipped directory of the demonstration package and execute these
commands to download the design and connect to the MicroBlaze processor:

$ cd KC705_Embedded_Kit/Video_Demo/ready_for_download

$ xmd

XMD% fpga -f download.bit

This command downloads the hardware bitstream into the FPGA but does not
download the software application:

XMD% connect mb mdm

This command connects to the MicroBlaze processor debug module:

XMD% dow Video_Demo.elf

XMD% con

Содержание Kintex-7 FPGA KC705

























Результаты поиска

Содержание Kintex-7 FPGA KC705

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Kintex-7 FPGA KC705, Начало работы

Результаты поиска

Содержание Kintex-7 FPGA KC705

Отзывы:

Бренды по названию

Популярные бренды