background image

FreeFlow Accxes Printer System and Web Print Management Tool Setup Guide 

3

 

NONE. Your choices will show on the screen, for example: (plt00t). An example queue 
name is "plt99" when NONE is selected. 
- Press the 

Update Printer

 button to set your choices. 

NOTE: 

 See the Configure Remote Printer Status Messages at the end of this document. 

 Select 

CONFIGURATION > NETWORK > TCP/IP

.   

- Check that the Subnet Mask, IP Address, and Gateway settings are correct. These are 
needed so that your workstation will be able to communicate with your FreeFlow Accxes 
compliant scanner and printer. 
- If the printer is not properly auto negotiating with the network, then set the 
Speed/Duplex to something other than "Auto".  The other selectable options are "10 
Mbps - Half Duplex", "10 Mbps - Full Duplex", 100 Mbps - Half Duplex", and "100 Mbps - 
Full Duplex". The Auto setting will properly auto negotiate with a YKE/YKE-N’s 1000 
Mbps switch. 
- Select 

HELP

 to access further information from the Help files. 

TCP/IP Address Parameters from the Printer 
Control Panel  

510, 8825, 8830, 8850 Printers: 

Perform the following steps: 

1. At 

the 

Printer Control Panel

, when the display shows <IDLE>, press

 ONLINE

.  

2.  When the display shows <

PAUSED

>, press 

ENTER

.  

3.  When the display shows <

UTILITIES

>, press 

NEXT

.  

4.  When the display shows <

SETUP I/O PORTS

>, press

 ENTER

.  

5.  When the display shows 

<SCSI

>, press 

NEXT

 until the display shows <

ETHERNET 

TCP/IP

>. Press 

ENTER

Once you have access the ETHERNET TCP/IP menu, perform the following steps at the printer 
control panel to enable DHCP or RARP/BOOTP: 

6. Press 

the 

NEXT

 key until 

DHCP ENABLE=OFF

 or 

RARP/BOOTP ENABLE=OFF

 is 

displayed.  

7. Press 

the 

ENTER 

key followed by the 

NEXT

 key to change the setting to 

ON

, then press 

the 

ENTER

 key.   

NOTE:

 Verify that you have DHCP enabled.

 

8. Press 

the 

EXIT

 key as many times as required to go back to 

PAUSED

 mode.  

9. Press 

the 

ONLINE

 

key to put the printer back on line. The display will show 

IDLE

.  

10.  Wait 60 seconds and cycle the printer power. The printer will reflect the new TCP/IP 

address after booting up.  

11. Printer a 

CONFIGURATION & SETTINGS TEST PRINT

 and save it for future reference.  

Содержание Wide Format 6030





















Отзывы: