Xerox Synergix 8850 Скачать руководство пользователя | Manualshive

Страница: 52 / 432

background image

03/2003

2-18

8850/ 510DP

Generic Clutch RAP, Generic Sensor RAP

Status Indicator RAPs

Generic Clutch RAP

Initial Actions

NOTE: This procedure can be used to check any clutch. Due to the generic format of this RAP
there will be no specific ADJ, PL or Diagnostic codes identified. The PWB names, voltages,
connectors, and pin numbers are fictitious. Refer to the appropriate BSD for the actual names
and numbers

Procedure

(Figure 1): Enter DIAGNOSTICS (General Procedures). Enter code [xxxx] to test the Clutch
(Refer to appropriate BSD for the specific code). Actuate the Clutch.

The Clutch energizes.

Y

N

Deactuate the clutch.

There is +24 VDC at J209-12 (use the actual connector/pin

number on the BSD) on the PWB (AX).
Y

N

Check the wire for an open circuit. If the wires are good, replace the Clutch (PL X.X).

Check the adjustment of the Clutch (ADJ X.X).
If the adjustment is good, replace the Clutch (PL X.X).

The Clutch and its circuit appear to be operating normally. Check the adjustment or alignment
of the Clutch.

Figure 1 Clutch (Generic)

Generic Sensor RAP

Initial Actions

NOTE: This procedure can be used to check any sensor. Due to the generic format of this RAP
there will be no specific ADJ, PL or Diagnostic codes identified. The PWB names, voltages,
connectors, and pin numbers are fictitious. Refer to the appropriate BSD for the actual names
and numbers.

•

Ensure that the Sensor is not blocked.

•

Clean the Sensor surfaces before using this procedure.

Procedure

(Figure 1): Enter DIAGNOSTICS (General Procedures). Enter code [xxxx] to test the Sensor
(Refer to appropriate BSD for the specific code). Block the Sensor.

The Display toggles

between [1] and [0].
Y

N
There is +5 +/-0.3 VDC at J60X/P60X pin X of the Main PWB.
Y

N
The + 5 VDC LED on the Main PWB is on
Y

N

Refer to the 1.2 DC Power RAP

Replace the Main PWB.

Check the wiring to the sensor for an open circuit.
If the wiring is good, replace the Sensor.

The Sensor and its circuit appear to be operating normally, check the adjustment or alignment
of the Sensor.

«
...
50
51
52
53
54
...
»

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synergix 8850

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

Бренд: CAB Страницы: 40

Бренд: QMS Страницы: 144

Бренд: Unimark Страницы: 38

imageRUNNER ADVANCE DX C478iZ

Бренд: Canon Страницы: 208

imageRUNNER ADVANCE DX C477iFZ

Бренд: Canon Страницы: 92

Бренд: Canon Страницы: 542

Бренд: Primera Страницы: 2

Бренд: TP Страницы: 10

Invent3d Series

Бренд: Inventorcloud Страницы: 4

DiMAGE Scan Elite 5400 II

Бренд: Konica Minolta Страницы: 38

WorkCentre BookMark 40

Бренд: Xerox Страницы: 12

Бренд: Ricoh Страницы: 4

Бренд: VuPoint Страницы: 20

3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...

Бренд: 3Com Страницы: 94

Бренд: Citizen Страницы: 46

Бренд: Konica Minolta Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды