manualshive.com logo in svg

Xerox Synergix 8850, Руководство по обслуживанию

Поделиться
Скачать
Xerox Synergix 8850 Скачать руководство пользователя страница 237

03/2003 

5-3

8850/ 510DP 

Introduction

Parts Lists

Introduction

Overview

The Parts List section identifies all part numbers and the corresponding location of all spared
subsystem components.

Organization

Parts Lists

Each item number in the part number listing corresponds to an item number in the related
illustration. All the parts in a given subsystem of the machine will be located in the same
illustration or in a series of associated illustrations.

Electrical Connectors and Fasteners

This section contains the illustrations and descriptions of the plugs, jacks, and fasteners used
in the machine. A part number listing of the connectors is included.

Common Hardware

The common hardware is listed in alphabetical order by the letter or letters used to identify
each item in the part number listing and in the illustrations. Dimensions are in millimeters
unless otherwise identified.

Part Number Index

This index lists all the spared parts in the machine in numerical order. Each number is followed
by a reference to the parts list on which the part may be found.

Other Information

Abbreviations

Abbreviations are used in the parts lists and the exploded view illustrations to provide
information in a limited amount of space. The following abbreviations are used in this manual:

Symbology

Symbology used in the Parts List section is identified in the Symbology section.

Service Procedure Referencing

If a part or assembly has an associated repair or adjustment procedure, the procedure number
will be listed at the end of the part description in the parts lists e.g. (REP 5.1, ADJ 5.3)

Table 1 

Abbreviation

Meaning

A0

841 x 1189 Millimetres

A1

594 x 841 Millimetres

A2

420 x 420 Millimetres

A3

297 x 594 Millimetres

A4

210 x 297 Millimetres

AWG

American Wire Gauge

EMI

Electro Magnetic Induction

GB

Gigabyte

KB

Kilobyte

MB

Megabyte

MM

Millimetres

NOHAD

Noise Ozone Heat Air Dirt

PL

Part List

P/O

Part of

REF

:

Refer to

SCSI

Small Computer Systems Interface

W/

With

W/O

Without

Table 2 

Operating Companies

Abbreviation

Meaning

EO

European Operations

NACO

North American Customer Operations

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды