Xerox Synergix 8850 Скачать руководство пользователя | Manualshive

Страница: 229 / 432

background image

03/2003

4-153

8850/ 510DP

ADJ 9.6

Repairs and Adjustments

ADJ 9.6 Augers

Purpose

The purpose is to set the Developer Auger and the Mix Auger to the correct angles in order to
ensure correct operation of the Developer Module.

WARNING

Switch off the Main Power Switch. Disconnect the Power Cord.

Check

NOTE: In order to see the flats on the augers, remove the Sump Shield using the Developer
Material removal procedure (

).

1.

Remove the Sump Shield.

2.

(Figure 1): Check for the correct orientation of the augers.

a.

The flats are at the end opposite the gears, approximately one inch from the ends of
the augers.

b.

Expose the flats using a brush to move the Developer Material.

c.

Looking down on the augers, check that the Developer Auger is pointing towards the
Magnetic Roll at an approximate 45 degree angle.

d.

Check that the last flats on the last two flutes on the Mix Auger are approximately
horizontal.

Figure 1 Checking for the Correct Orientation of the Augers

Adjustment

NOTE: In order to position the flats on the augers, the Developer material must first be
removed. In order to rotate the augers individually, the gears at the drive end of the Developer
module must be removed.

1.

Remove the Developer Material (

).

2.

(Figure 1): Position the flats on the augers by rotating the appropriate gear at the drive
end of the Developer Module.

a.

The flats are at the end opposite the gears, approximately one inch from the ends of
the augers.

NOTE: A sheet of paper is used in the photographs so that the auger can be seen.
The Toner Cartridge Support Hub is also removed for clarity.

b.

Looking down on the augers, position the Developer Auger to point towards the
Magnetic Roll at an approximate 7 o’clock position (45 degree angle).

Figure 2 Adjusting the Developer Auger

Magnetic Roll

Developer Auger

Mix Auger

45
Degrees

1

Rotate the Developer
Auger until the flat on the
auger flute is at the 7
o’clock position

PAPER

«
...
227
228
229
230
231
...
»

Содержание Synergix 8850

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synergix 8850

Бренд: GCC Technologies Страницы: 63

Бренд: gCreate Страницы: 9

Бренд: GCC Technologies Страницы: 9

Бренд: GCC Technologies Страницы: 12

Бренд: gCreate Страницы: 21

Бренд: GCC Technologies Страницы: 199

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 455

Бренд: JCM Страницы: 22

VarioPrint 1055

Бренд: OcÃ© Страницы: 194

Бренд: Oce Страницы: 12

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 148

Бренд: Wasp Страницы: 2

Бренд: Oki Страницы: 95

Бренд: Olivetti Страницы: 78

Бренд: Konica Minolta Страницы: 15

Бренд: Oki Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды