![background image](http://html1.mh-extra.com/html/xerox/phaser-4620/phaser-4620_service-manual_4208243055.webp)
5/2011
2-31
Phaser 4600/4620 Printer Service Manual
07-510-00, 07-700-00, 07-520-00
Status Indicator RAPS
Revision - Xerox Internal Use Only
07-510-00, 07-700-00 Paper Empty at Tray 6
07-510-00 The Tray 6 No Paper Sensor indicates Tray 6 is empty.
07-700-00 Tray 6 Out of Paper.
BSD-Reference:
WD 13
Initial Actions
1.
Check the No Paper Sensor Actuator.
Procedure
WARNING
Use safe handling procedures when removing the module. Refer to
GP 15
. The module
is heavy.
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Check the No Paper Sensor Actuator. The actuator is undamaged and motion is good.
Y
N
Repair or replace the Tray 6 No Paper Sensor Actuator.
Select
dC330
code 07-610 to test the sensor. The sensor signal changes (high/low).
Y
N
Remove the IOT, Tray 3, 4 and 5. Check the option harness connections. The
harness
connectors are undamaged.
Y
N
Replace any damaged harnesses.
Exchange Feeder positions. The error changes to the new feeder position.
Y
N
Check the IOT Lower Option Harness. The harness is undamaged.
Y
N
Replace the Lower Option Harness,
REP 10.5
.
Replace the MCU Board,
REP 3.4
.
Replace the No Paper Sensor (
REP 7.35
), then retest. The signal changes.
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN3 on the Feeder Board, then
retest. The sensor signal changes.
Y
N
Replace the Feeder Board,
REP 7.28
.
Reassemble and perform
SCP 6
Final Actions.
Reassemble and perform
SCP 6
Final Actions.
Replace the MCU Board,
REP 3.4
.
07-520-00 Tray 6 is Open RAP
07-520-00 The Size Switch indicates Tray 6 is not completely installed.
BSD-Reference:
WD 13
Initial Actions
1.
Close the Tray.
2.
Check the Size Switch.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Remove Tray 6and inspect the Size Switch. The Size Switch is undamaged.
Y
N
Replace the Size Switch,
REP 7.30
, then retest.
Select
dC330
code 07-600 to test the switch. The switch signals change (open/closed).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN5 on the Feeder Board, then retest.
The sensor signal changes.
Y
N
Replace the Feeder Board,
REP 7.28
.
Reassemble and perform
SCP 6
Final Actions.
Replace these components in order until the error is corrected.
1.
Size Switch,
PL 8.30 Item 9
2.
Feeder Board,
PL 8.30 Item 7
3.
MCU Board,
PL 3.10 Item 3
Содержание Phaser 4620
