![background image](http://html1.mh-extra.com/html/xerox/phaser-4620/phaser-4620_service-manual_4208243049.webp)
5/2011
2-25
Phaser 4600/4620 Printer Service Manual
07-210-00, 07-220-00
Status Indicator RAPS
Revision - Xerox Internal Use Only
07-210-00 Paper Empty at Tray 3 RAP
07-210-00 The Tray 3 No Paper indicates the Tray is empty.
BSD-Reference:
WD 3
Initial Actions
1.
Add media to the Tray.
2.
Check the No Paper Sensor Actuator.
3.
Check for obstruction of the Pick mechanism.
Procedure
WARNING
Use safe handling procedures when removing the module. Refer to
GP 15
. The module
is heavy.
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Check the Tray 3 No Paper Sensor Actuator. The actuator is undamaged and motion is
good.
Y
N
Repair or replace the Tray 3 No Paper Sensor Actuator.
Select
dC330
code 07-310 to test the sensor. The sensor signal changes (high/low).
Y
N
Remove the IOT, from the Feeder and check the Upper Option Harness,
PL 8.30 Item 10
.
The harness is undamaged.
Y
N
Replace the harness,
REP 7.31
.
Check the IOT Lower Option Harness. The harness is undamaged.
Y
N
Replace the IOT Lower Option Harness,
REP 10.5
.
Replace the Tray 3 No Paper Sensor (
REP 7.35
), then retest. The sensor signal
changes.
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN3 on the Feeder Board, then
retest. The sensor signal changes.
Y
N
Replace the MCU Board,
REP 3.4
.
Reassemble and perform
SCP 6
Final Actions.
Reassemble and perform
SCP 6
Final Actions.
Replace the MCU Board,
REP 3.4
.
07-220-00 Tray 3 is Open RAP
07-220-00 The Size Switch indicates the Tray is not fully installed.
BSD-Reference:
WD 3
Initial Actions
1.
Close the Tray.
2.
Check the Size Switch.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Remove Tray 3 and inspect the Size Switch. The Size Switch is undamaged.
Y
N
Replace the Size Switch,
REP 7.30
, then retest.
Select
dC330
code 07-300 to test the switch. The switch signals change (open/closed).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN5 on the Feeder Board, then retest.
The sensor signal changes.
Y
N
Replace the Feeder Board,
REP 7.28
.
Reassemble and perform
SCP 6
Final Actions.
Replace these components in order until the error is corrected.
1.
Size Switch,
PL 8.30 Item 9
2.
Feeder Board,
PL 8.30 Item 7
3.
MCU Board,
PL 3.10 Item 3
Содержание Phaser 4620
