![background image](http://html1.mh-extra.com/html/xerox/phaser-4620/phaser-4620_service-manual_4208243048.webp)
5/2011
2-24
Phaser 4600/4620 Printer Service Manual
07-120-00, 07-130-00
Revision - Xerox Internal Use Only
Status Indicator RAPS
07-120-00 Tray 2 is Open RAP
07-120-00 The Size Switch indicates the Tray is not fully installed.
BSD-Reference:
WD 3
Initial Actions
1.
Close the Tray.
2.
Check the Size Switch.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Remove Tray 2 and inspect the Size Switch. The Size Switch is undamaged.
Y
N
Replace the Size Switch,
REP 7.30
, then retest.
Select
dC330
code 07-200 to test the switch. The switch signals change (open/closed).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN11 on the MCU Board, then retest.
The sensor signal changes.
Y
N
Replace the MCU Board,
REP 3.4
.
Replace these components in order until the error is corrected.
1.
Size Switch,
PL 3.10 Item 9
2.
MCU Board,
PL 3.10 Item 3
07-130-00 Jam 0 in Tray 2 RAP
07-130-00 Media present at the Take Away Sensor.
BSD-Reference:
WD 3
Initial Actions
1.
Check media condition.
2.
Check for obstructions in the media path.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The
rollers are undamaged and clean.
Y
N
Clean or replace the rollers.
Check for obstructions or debris in the media path. The media path is clear.
Y
N
Clear the media path of obstructions or debris.
Check Tray 2 pick assembly (
PL 8.15
) motion. Pick assembly motion is good.
Y
N
Repair improper pick assembly motion.
Select
dC330
code 08-820 to test the Feed Clutch. The clutch is engaged (on/off).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN12 on the MCU Board, then retest.
The clutch is engaged.
Y
N
Replace the Feed Clutch,
REP 4.2
.
Reassemble and perform
SCP 6
Final Actions.
Select
dC330
code 04-580 to test the Feed Drive Assembly. The Feed Drive Assembly
rotates (on/off).
Y
N
Remove the Right Cover (
REP 28.2
) and reseat CN12 on the MCU Board, then retest.
The Feed Drive Assembly rotates.
Y
N
Replace the Feed Drive Assembly,
REP 4.4
.
Reassemble and perform
SCP 6
Final Actions.
Replace the MCU Board,
REP 3.4
.
Содержание Phaser 4620
