![background image](http://html1.mh-extra.com/html/xerox/phaser-4620/phaser-4620_service-manual_4208243045.webp)
5/2011
2-21
Phaser 4600/4620 Printer Service Manual
04-730-00
Status Indicator RAPS
Revision - Xerox Internal Use Only
04-730-00 HCF Lift Error RAP
04-730-00 HCF Level Sensor did not change state within 13 seconds of Lift Motor activation.
NOTE: Optional Tray numbering varies by configuration. When testing HCF components, use
the
dC330
codes appropriate for the HCF’s position. For example, if the configuration is 5 trays
and the 5th tray is the HCF, use Tray 5 control codes.
BSD-Reference:
WD 16
Initial Actions
•
Open and close the HCF Front Door.
•
Check for obstructions blocking bottom plate movement.
Procedure
WARNING
Use safe handling procedures when removing the module. Refer to
GP 15
. The module
is heavy.
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Raise and lower the lower lift plate. The lower lift plate moves up and down smoothly.
Y
N
Repair or replace damaged components.
Check Pick Assembly (
PL 8.25
) motion. Pick assembly motion is good.
Y
N
Repair improper Pick Assembly motion.
Select
dC330
code for the HCF position. The sensor is operational (high/low).
Y
N
Repair or replace the Level Sensor,
REP 8.50
.
Check the Lift Gear,
PL 8.35 Item 4
. The gear is undamaged and properly installed.
Y
N
Replace the Lift Gear,
REP 7.8
.
Test HCF Lift Motor operation by opening and closing the front door. The Lift Motor rotates.
Y
N
Remove the IOT, Tray 3 and Tray 4 from the HCF and check the HCF Option Harness,
PL
7.25 Item 15
. The harness is undamaged.
Y
N
Replace the harness ().
Check the IOT Lower Option Harness. The harness is undamaged.
Y
N
Replace the Lower Option Harness,
REP 10.5
.
Remove the Right Cover (), reseat CN2 on the Control Board and CN1, CN2 on the
Jumper Board, then retest. The Lift Motor rotates.
Y
N
Replace the Lift Motor, (), then retest. The Lift Motor rotates.
Y
N
Replace the Control Board, ().
Reassemble and perform
SCP 6
Final Actions.
Reassemble and perform
SCP 6
Final Actions.
Replace these components in order until the error is corrected.
1.
Feeder Assembly,
PL 8.25 Item 16
2.
Control Board,
PL 7.25 Item 18
3.
MCU Board,
PL 3.10 Item 3
A
A
Содержание Phaser 4620
