![background image](http://html1.mh-extra.com/html/xerox/phaser-4620/phaser-4620_service-manual_4208243042.webp)
5/2011
2-18
Phaser 4600/4620 Printer Service Manual
04-200-00, 04-300-00
Revision - Xerox Internal Use Only
Status Indicator RAPS
Y
N
Replace the Feeder Board,
REP 7.28
.
Reassemble and perform
SCP 6
Final Actions.
Reassemble and perform
SCP 6
Final Actions.
Remove the IOT and check the IOT Lower Option Harness. The harness is undamaged.
Y
N
Replace the Lower Option Harness,
REP 10.5
.
Replace these components in order until the error is corrected.
1.
Tray,
PL 7.10 Item 23
2.
Feeder Board,
PL 8.30 Item 7
3.
MCU Board,
PL 3.10 Item 3
04-300-00 Tray 4 Lift Error RAP
04-300-00 Tray 4 Level Sensor did not change state within 13 seconds of Lift Motor activation.
BSD-Reference:
WD 13
Initial Actions
•
Remove and replace Tray 4.
•
Check for obstructions blocking bottom plate movement.
•
Reorder Feeder position to isolate the problem.
Procedure
WARNING
Use safe handling procedures when removing the module. Refer to
GP 15
. The module
is heavy.
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Cycle system power. The error message is displayed.
Y
N
Complete.
Check Tray 4 bottom plate linkage and sector gear condition. Use an alternate Tray to test lift
operation.The Tray is undamaged.
Y
N
Replace the Tray.
Check the Pick Assembly (
PL 8.20
) motion. Pick assembly motion is good.
Y
N
Repair improper Pick Assembly motion.
Select
dC330
code 07-450. The sensor is operational (high/low).
Y
N
Repair or replace the Level Sensor,
REP 7.37
.
Check the Lift Gear,
PL 8.35 Item 4
. The gear is undamaged and properly installed.
Y
N
Replace the Lift Gear,
REP 7.8
.
Remove the IOT and Tray 3 from the Feeder. Reassemble the system to exchange Feeder
positions. The error message changes to the new feeder position.
Y
N
Check the IOT Lower Option Harness. The harness is undamaged.
Y
N
Replace the Lower Option Harness,
REP 10.5
.
Replace the MCU Board,
REP 3.4
.
A
B
A
Содержание Phaser 4620
